PART 2 | الجزء الثاني

DC Circuit Analysis: Historical Evolution of Solution Methods

تحليل دارات التيار المستمر: التطور التاريخي لطرق الحل

Electrical Engineering Fundamentals 1 | أسس الهندسة الكهربائية 1

10-Question Quiz | الاختبار

Before Analysis: Basic Circuit Concepts

قبل التحليل: المفاهيم الأساسية للدارات الكهربائية

1. Electric charge

Electric charge is a physical property of matter, denoted by \(q\) and measured in coulombs (\(\mathrm{C}\)). Charge can be positive or negative: a proton carries positive charge and an electron carries negative charge.

The magnitude of the electron’s charge is:

1. الشحنة الكهربائية

الشحنة الكهربائية خاصية فيزيائية للمادة، نرمز لها بالرمز \(q\)، وتقاس بوحدة الكولوم \(\mathrm{C}\). توجد شحنات موجبة وأخرى سالبة؛ فالبروتون يحمل شحنة موجبة، والإلكترون يحمل شحنة سالبة.

مقدار شحنة الإلكترون هو:

\[e=1.602176634\times10^{-19}\ \mathrm{C},\qquad q_e=-e\]

A charge magnitude of \(1\ \mathrm{C}\) therefore corresponds to approximately \(6.24\times10^{18}\) electrons.

Free electrons in a metal move randomly. An electric field within the conductor produces a net drift superimposed on this random motion, giving rise to an electric current.

لذلك، يعادل مقدار شحنة \(1\ \mathrm{C}\) مقدار شحنة نحو \(6.24\times10^{18}\) إلكترونا.

في الأسلاك المعدنية توجد إلكترونات حرة تتحرك عشوائيا. وعند إنشاء مجال كهربائي داخل السلك، تظهر لها حركة انجراف صافية تضاف إلى حركتها العشوائية، فتؤدي إلى مرور تيار كهربائي.

2. Electric current

Electric current is the rate at which electric charge crosses a conductor’s cross-section. It describes charge passing per unit time, not the speed of the electrons.

If a net charge \(\Delta q\) crosses the section during \(\Delta t\), the average current is:

2. التيار الكهربائي

التيار الكهربائي هو معدل مرور الشحنة الكهربائية عبر مقطع من الناقل بالنسبة إلى الزمن. أي إنه يصف كمية الشحنة التي تعبر هذا المقطع في كل ثانية، وليس سرعة حركة الإلكترونات.

إذا عبرت شحنة صافية مقدارها \(\Delta q\) خلال مدة \(\Delta t\)، فإن التيار المتوسط يساوي:

\[I_{\mathrm{avg}}=\frac{\Delta q}{\Delta t}\]

The instantaneous current is the derivative of the cumulative net charge that has crossed the section:

أما قيمة التيار اللحظية فهي مشتقة الشحنة الصافية المتراكمة التي عبرت المقطع بالنسبة إلى الزمن:

\[i(t)=\frac{dq(t)}{dt}\]

Current is measured in amperes (\(\mathrm{A}\)):

يقاس التيار بوحدة الأمبير \(\mathrm{A}\)، حيث:

\[1\ \mathrm{A}=1\ \frac{\mathrm{C}}{\mathrm{s}}\]

A current of \(1\ \mathrm{A}\) means that a net charge of \(1\ \mathrm{C}\) passes through the cross-section each second.

أي إن تيارا شدته \(1\ \mathrm{A}\) يعني مرور شحنة صافية مقدارها \(1\ \mathrm{C}\) عبر مقطع الناقل كل ثانية.

3. Charge–current relationship

For a constant current, the charge passing during a time interval is:

3. العلاقة بين الشحنة والتيار

عندما يكون التيار ثابتا، نحسب الشحنة التي تعبر المقطع خلال مدة \(\Delta t\) بالعلاقة:

\[\Delta q=I\,\Delta t\]

Worked example: A constant current of \(2\ \mathrm{A}\) flows through a wire for \(5\ \mathrm{s}\). The charge crossing its section is:

مثال محلول: إذا مر تيار ثابت شدته \(2\ \mathrm{A}\) في سلك لمدة \(5\ \mathrm{s}\)، فإن الشحنة التي تعبر مقطعه تساوي:

\[\Delta q=2\times5=\boxed{10\ \mathrm{C}}\]

For a time-varying current, integrate over the required interval:

أما إذا تغير التيار مع الزمن، فنحسب الشحنة بالتكامل:

\[\Delta q=\int_{t_1}^{t_2}i(t)\,dt\]

The signed area under the current–time curve represents the net charge that crossed the section.

المساحة الجبرية تحت منحنى التيار مع الزمن تمثل الشحنة الصافية التي عبرت المقطع.

4. Current direction

Conventional current points in the direction of positive-charge motion. In metallic wires, electrons drift in the opposite direction.

When solving a circuit, choose a reference arrow for each current:

  • A positive result means current flows in the arrow’s direction.
  • A negative result means it flows against the arrow; it does not mean the solution is incorrect.

4. اتجاه التيار

نعرّف الاتجاه الاصطلاحي للتيار بأنه اتجاه حركة الشحنات الموجبة. لذلك، في الأسلاك المعدنية يكون اتجاه حركة الإلكترونات معاكسا لاتجاه التيار الاصطلاحي.

عند حل الدارات نختار سهما مرجعيا لكل تيار:

  • إذا كانت القيمة المحسوبة موجبة، فالتيار يسري باتجاه السهم.
  • إذا كانت سالبة، فالتيار يسري بعكس السهم، ولا يعني ذلك أن الحل خاطئ.
Key idea: In a simple battery–resistor circuit, the resistor does not consume charge; electrical energy is converted to heat. In steady state, the charge entering the resistor each second equals the charge leaving it. This prepares us for Kirchhoff’s current law.
فكرة أساسية: في دارة بسيطة تضم بطارية ومقاومة، لا تستهلك المقاومة الشحنات؛ بل تتحول فيها الطاقة الكهربائية إلى حرارة. وفي الحالة المستقرة، تكون كمية الشحنة الداخلة إلى المقاومة في كل ثانية مساوية للكمية الخارجة منها، وهو تمهيد لفهم قانون كيرشوف للتيار.

5. Voltage and potential difference

5. الجهد وفرق الجهد

Voltage describes energy transferred per unit charge. The voltage between two points is their potential difference. A chosen reference node is assigned zero potential; this does not necessarily mean a physical earth connection.

يصف الجهد الطاقة المنقولة لكل وحدة شحنة. وفرق الجهد بين نقطتين هو الفرق بين كمونيهما الكهربائيين. نختار عقدة مرجعية ونعطيها جهدا صفريا، ولا يعني ذلك بالضرورة اتصالها بالأرض فعليا.

\[v_{ab}=V_a-V_b,\qquad 1\ \mathrm{V}=1\ \mathrm{J/C}\]

The + sign at a and − sign at b define the reference for \(v_{ab}\). If \(V_a=12\,\mathrm V\) and \(V_b=0\), then \(v_{ab}=12\,\mathrm V\) and \(v_{ba}=-12\,\mathrm V\).

Example: A \(12\,\mathrm{V}\) source supplying a charge of 2 C transfers 24 J of energy to the external circuit.

تحدد العلامة + عند a والعلامة − عند b مرجع الجهد \(v_{ab}\). إذا كان \(V_a=12\,\mathrm V\) و\(V_b=0\)، فإن \(v_{ab}=12\,\mathrm V\) و\(v_{ba}=-12\,\mathrm V\).

مثال: عندما يزود منبع بجهد \(12\,\mathrm{V}\) الدارة الخارجية بشحنة مقدارها 2 C، فإنه ينقل إليها طاقة مقدارها 24 J.

\[\Delta E=V\,\Delta q=12\times2=24\ \mathrm J\]

6. The circuit and the current path

6. الدارة الكهربائية ومسار التيار

A simple circuit contains a source, connecting wires, and a load that receives electrical energy. A sustained DC current requires a closed conducting path.

  • Closed circuit: a complete path is available.
  • Open circuit: the ideal gap carries zero current, but a voltage may exist across it.
  • Short circuit: an ideal zero-resistance connection has zero voltage across it; its current depends on the rest of the circuit.

تتكون الدارة البسيطة من منبع وأسلاك توصيل وحمل يستقبل الطاقة الكهربائية. يتطلب استمرار التيار المستمر مسارا ناقلا مغلقا.

  • الدارة المغلقة: يتوفر مسار كامل لمرور التيار.
  • الدارة المفتوحة: لا يمر تيار عبر القطع المثالي، لكن قد يوجد فرق جهد بين طرفيه.
  • القصر الكهربائي: وصلة مثالية مقاومتها صفر وفرق الجهد بين طرفيها صفر، ويتحدد تيارها وفق بقية الدارة.
+−12 VR = 6 ΩISource → load | المنبع يغذي الحمل

Never connect a wire directly across a real battery’s terminals: the resulting current can be very large. A nonzero ideal voltage source connected directly to an ideal short gives an inconsistent ideal circuit model.

لا توصل سلكا مباشرة بين قطبي بطارية حقيقية؛ فقد ينشأ تيار كبير جدا. أما وصل منبع جهد مثالي غير صفري بقصر مثالي مباشرة فينتج نموذجا مثاليا غير متسق.

7. Resistance and conductance

7. المقاومة والمواصلة الكهربائية

Resistance describes how a resistive element opposes current. Its symbol is R and its unit is the ohm (Ω). Conductance describes ease of conduction and is measured in siemens (S).

تصف المقاومة ممانعة العنصر المقاوم لمرور التيار. نرمز لها بـ R وتقاس بالأوم (Ω). أما المواصلة فتعبر عن سهولة التوصيل، وتقاس بالسيمنس (S).

\[G=\frac{1}{R},\qquad R=5\ \Omega\ \Longrightarrow\ G=0.2\ \mathrm S\]

Resistance of a uniform conductor

For a uniform wire, resistance increases with length and resistivity and decreases with cross-sectional area. Here L is in m, A in mm², and ρ in Ω·mm²/m.

حساب مقاومة موصل منتظم المقطع

تزداد مقاومة السلك بازدياد طوله ومقاوميته النوعية، وتنخفض بازدياد مساحة مقطعه. يقاس الطول L بالمتر، والمقطع A بالـ mm²، والمقاومية النوعية ρ بالـ Ω·mm²/m.

\[R=\rho\frac{L}{A}\]

Approximate resistivity at 20°C: copper 0.0172 Ω·mm²/m; aluminium 0.0282 Ω·mm²/m. Values vary with purity and alloy.

المقاومية النوعية التقريبية عند 20°C: النحاس 0.0172 Ω·mm²/m، والألمنيوم 0.0282 Ω·mm²/m. تتغير القيم باختلاف النقاوة والسبيكة.

Worked example: single-core copper wire

A 100 m copper conductor has a cross-sectional area of 1 mm² at 20°C. Its one-way resistance is \(1.72\,\Omega\). If the circuit uses an identical return conductor, the total conductor length is 200 m and the loop resistance is \(3.44\,\Omega\) (excluding connections).

مثال محلول: سلك نحاسي مفرد

سلك نحاسي بطول 100 m ومقطع 1 mm² عند 20°C. مقاومته \(1.72\,\Omega\). إذا احتاجت الدارة إلى سلك عودة مماثل، يصبح طول مسار التيار 200 m ومقاومة السلكين \(3.44\,\Omega\)، دون احتساب مقاومات الوصلات.

\[R_{20}=0.0172\frac{100}{1}=1.72\ \Omega,\qquad R_{\mathrm{loop}}=2(1.72)=3.44\ \Omega\]

Temperature correction

For a moderate temperature range, metallic conductor resistance is approximately linear with temperature. Typical coefficients at 20°C: copper α = 0.00393 /°C; aluminium α = 0.00403 /°C. For the copper wire above, heating to 60°C gives about \(1.99\,\Omega\).

تصحيح المقاومة مع تغير درجة الحرارة

ضمن مجال حراري معتدل، تتغير مقاومة الموصلات المعدنية تقريبا خطيا مع درجة الحرارة. معامل النحاس عند 20°C هو 0.00393 /°C، وللألمنيوم 0.00403 /°C. عند تسخين السلك النحاسي السابق إلى 60°C تصبح مقاومته نحو \(1.99\,\Omega\).

\[R_T=R_{20}[1+\alpha_{20}(T-20)],\qquad R_{60}=1.72[1+0.00393(60-20)]\approx1.99\ \Omega\]

Interactive wire-resistance calculator

Change the conductor properties and observe the calculated resistance instantly.

حاسبة تفاعلية لمقاومة السلك

غيّر خصائص الموصل ولاحظ تغير المقاومة المحسوبة مباشرة.

Resistance at 20°C | المقاومة عند 20°C
1.720 Ω
Resistance at selected temperature | المقاومة عند الحرارة المختارة
1.720 Ω
Two-wire loop | مقاومة سلكي الذهاب والعودة
3.440 Ω

Resistance versus temperature — Copper and aluminium

Both curves use the length and area selected above. The vertical dashed line indicates the selected temperature.

المقاومة بدلالة درجة الحرارة — النحاس والألمنيوم

يستخدم المنحنيان الطول والمقطع المحددين أعلاه. يشير الخط المتقطع العمودي إلى درجة الحرارة المختارة.

Temperature / درجة الحرارة (°C)Resistance / المقاومة (Ω)
● Copper | النحاس: 1.720 Ω● Aluminium | الألمنيوم: 2.820 Ω

Straight lines arise from the approximate linear model over 0–100°C; real material behavior is not perfectly linear over all temperatures. | الخطية ناتجة عن النموذج التقريبي ضمن المجال 0–100°C، ولا تعني أن سلوك المادة خطي تماما في كل درجات الحرارة.

Approximate linear temperature model; uniform conductor. The two-wire result assumes equal outgoing and return lengths. | نموذج حراري خطي تقريبي لموصل منتظم، مع افتراض تساوي طول سلكي الذهاب والعودة.

Self-check: How do resistance and conductor heating change if the length doubles or the cross-sectional area doubles? For a given current, calculate voltage drop and loss using ΔV = IR and P = I²R.

تمرين ذاتي: كيف تتغير المقاومة والتسخين إذا تضاعف طول السلك أو تضاعفت مساحة مقطعه؟ عند تيار معلوم احسب هبوط الجهد والفقد باستخدام ΔV = IR و P = I²R.

A resistor converts electrical energy into heat. Its resistance may depend on material, geometry and temperature. Ohm’s law and its calculation examples are introduced in the historical card below.

تحول المقاومة الطاقة الكهربائية إلى حرارة. وتتأثر مقاومتها بالمادة والأبعاد ودرجة الحرارة. سنعرض قانون أوم وأمثلته الحسابية في بطاقته التاريخية أدناه.

8. Voltage and current sources

8. منابع الجهد والتيار

A voltage source specifies voltage; the connected circuit determines its current. A current source specifies current; the connected circuit determines its voltage. A source may supply or absorb energy, as when a battery is charged.

For example, “12 V” on a voltage source does not imply a fixed current of \(12\,\mathrm{A}\).

منبع الجهد يحدد الجهد، وتتحدد شدة تياره وفق الدارة المتصلة به. ومنبع التيار يحدد التيار، ويتحدد جهده وفق الدارة. ويمكن للمنبع أن يزود الطاقة أو يمتصها، كما يحدث عند شحن البطارية.

مثلا: لا تعني كتابة \(12\,\mathrm{V}\) على منبع جهد أنه يمرر تيارا ثابتا مقداره \(12\,\mathrm{A}\).

Ideal and practical models: an ideal voltage source has zero internal resistance; a simple practical model adds a series resistance. An ideal current source has infinite internal resistance; a simple practical model adds a parallel resistance. Real sources also have operating limits.

النماذج المثالية والحقيقية: المقاومة الداخلية لمنبع الجهد المثالي صفر، ويضيف نموذج حقيقي مبسط مقاومة على التوالي. أما المقاومة الداخلية لمنبع التيار المثالي فلا نهائية، ويضيف نموذج حقيقي مبسط مقاومة على التوازي. وللمنابع الحقيقية حدود تشغيل أيضا.

Worked example: the internal resistance of a voltage source

مثال عددي: المقاومة الداخلية لمنبع الجهد

A practical voltage-source model consists of an ideal source and an internal resistance in series with the load. Consider a source with emf \(E=12\,\mathrm V\) supplying a load \(R_L=6\,\Omega\). This example previews Ohm’s law and series resistance, explained in the historical cards below.

يتكون نموذج منبع الجهد الحقيقي من منبع مثالي ومقاومة داخلية على التوالي مع الحمل. لنأخذ منبعا قوته المحركة الكهربائية \(E=12\,\mathrm V\) يغذي مقاومة حمل \(R_L=6\,\Omega\). يستخدم المثال تمهيديا قانون أوم وجمع مقاومات التوالي، وسنشرحهما في البطاقات التاريخية أدناه.

1. Ideal voltage source

Its internal resistance is zero, so the full source voltage appears across the load.

1. منبع الجهد المثالي

مقاومته الداخلية صفر؛ لذلك يظهر كامل جهد المنبع على الحمل.

\[R_{\mathrm{int}}=0,\qquad I_L=\frac{12}{6}=\boxed{2\ \mathrm A},\qquad V_L=\boxed{12\ \mathrm V}\]

2. Practical model with series internal resistance

Assume an internal resistance of \(1\,\Omega\) in series with the \(6\,\Omega\) load. The same current passes through both resistances.

2. نموذج حقيقي بمقاومة داخلية متسلسلة

نفترض مقاومة داخلية \(1\,\Omega\) على التوالي مع الحمل \(6\,\Omega\). يمر التيار نفسه في المقاومتين.

\[R_{\mathrm{total}}=R_{\mathrm{int}}+R_L=1+6=7\ \Omega\]
\[I_L=\frac{E}{R_{\mathrm{int}}+R_L}=\frac{12}{7}\approx\boxed{1.714\ \mathrm A}\]

The voltage drop across the internal resistance is:

هبوط الجهد على المقاومة الداخلية:

\[V_{\mathrm{int}}=I_LR_{\mathrm{int}}=\frac{12}{7}\times1\approx1.714\ \mathrm V\]

The terminal voltage, which is also the load voltage, becomes:

يصبح جهد طرفي المنبع، وهو نفسه جهد الحمل:

\[V_L=E-I_LR_{\mathrm{int}}=12-\frac{12}{7}=\frac{72}{7}\approx\boxed{10.286\ \mathrm V}\]

The model’s emf remains \(12\,\mathrm{V}\), but its terminal voltage drops under load because of the internal resistance. With the load disconnected, current is zero and the terminal voltage is \(12\,\mathrm{V}\) in this model.

تبقى القوة المحركة الكهربائية للمنبع في هذا النموذج \(12\,\mathrm{V}\)، لكن جهد طرفيه تحت الحمل ينخفض بسبب المقاومة الداخلية. وعند فصل الحمل يصبح التيار صفرا، ويعود جهد الطرفين إلى \(12\,\mathrm{V}\) في هذا النموذج.

Comparison: E = 12 V, Rₗ = 6 Ω | مقارنة عند تثبيت المنبع والحمل
Series internal resistance
المقاومة الداخلية المتسلسلة
Load current
تيار الحمل
Load voltage
جهد الحمل
1 Ω1.714 A10.286 V
0.1 Ω1.967 A11.803 V
0 Ω (Ideal | مثالي)2 A12 V

A smaller series internal resistance makes a voltage source closer to ideal. Numerical values in the table are rounded to three decimal places.

كلما صغرت المقاومة الداخلية المتسلسلة لمنبع الجهد، اقترب سلوكه من المنبع المثالي. القيم العددية في الجدول مقربة إلى ثلاث منازل عشرية.

3. Operating limits: maximum output current

In a separate example, consider a regulated \(12\,\mathrm{V}\) supply with a \(2\,\mathrm{A}\) current limit. Neglect internal voltage drop here to isolate current limiting; this is not the preceding \(1\,\Omega\) model.

  • A \(6\,\Omega\) load requires \(2\,\mathrm{A}\), so the supply can maintain \(12\,\mathrm{V}\) at its current limit.
  • A \(3\,\Omega\) load would require \(4\,\mathrm{A}\) to maintain \(12\,\mathrm{V}\), exceeding the limit.

3. حدود التشغيل: أقصى تيار خرج

في مثال مستقل، نفترض مزود جهد منظما على \(12\,\mathrm{V}\) وحد التيار الأقصى له \(2\,\mathrm{A}\). نهمل هنا هبوط الجهد الداخلي لتوضيح تحديد التيار وحده؛ فهذا ليس نموذج المقاومة \(1\,\Omega\) السابق.

  • مع حمل \(6\,\Omega\)، يحتاج إلى \(2\,\mathrm{A}\)، فيستطيع توفير \(12\,\mathrm{V}\) عند حد تياره الأقصى.
  • مع حمل \(3\,\Omega\)، يحتاج إلى \(4\,\mathrm{A}\) للمحافظة على \(12\,\mathrm{V}\)، وهذا يتجاوز الحد المسموح.
\[I_{\mathrm{required}}=\frac{12}{3}=4\ \mathrm A>2\ \mathrm A\]

If the supply enters constant-current mode at \(2\,\mathrm{A}\), the load voltage drops to:

إذا انتقل المزود إلى وضع تحديد التيار عند \(2\,\mathrm{A}\)، ينخفض جهد الحمل إلى:

\[V_L=I_{\mathrm{limit}}R_L=2\times3=\boxed{6\ \mathrm V}\]

The supply may instead shut down for protection, depending on its design. The current limit is an additional constraint that series internal resistance alone does not describe.

وقد يفصل المزود للحماية بدلا من ذلك، بحسب تصميمه. حد التيار قيد إضافي لا تمثله المقاومة الداخلية المتسلسلة وحدها.

Compare with the next example: ideal voltage source → zero series internal resistance; ideal current source → infinite parallel internal resistance.

قارن بالمثال التالي: منبع الجهد المثالي: مقاومة داخلية متسلسلة تساوي صفرا. منبع التيار المثالي: مقاومة داخلية متوازية تؤول إلى اللانهاية.

Worked example: why is a current source’s internal resistance infinite?

مثال عددي: لماذا تكون المقاومة الداخلية لمنبع التيار المثالي لا نهائية؟

The internal resistance is connected in parallel with the ideal current source, not in series with the load. Increasing it reduces the current diverted through this internal branch. Consider a \(2\,\mathrm{A}\) source supplying a \(10\,\Omega\) load.

The example previews Ohm’s law and current division, which are explained in the historical cards below.

المقاومة الداخلية موصولة على التوازي مع منبع التيار المثالي، وليست على التوالي مع الحمل. كلما كبرت، قل التيار المتسرب عبر هذا الفرع الداخلي. لنأخذ منبع تيار قيمته \(2\,\mathrm{A}\) يغذي مقاومة حمل \(10\,\Omega\).

يستخدم المثال تمهيديا قانون أوم وتقسيم التيار، وسنشرح هاتين العلاقتين في البطاقات التاريخية أدناه.

1. Ideal current source

As the internal resistance tends to infinity, its branch acts as an open circuit. No current flows through it, and the full \(2\,\mathrm{A}\) reaches the load.

1. منبع التيار المثالي

عندما تؤول المقاومة الداخلية إلى اللانهاية، يشبه فرعها دارة مفتوحة، فلا يمر فيه تيار. لذلك يصل كامل تيار المنبع، أي \(2\,\mathrm{A}\)، إلى الحمل.

\[R_{\mathrm{int}}\to\infty,\quad I_{\mathrm{int}}=0,\quad I_L=2\ \mathrm A\]
\[V=I_LR_L=2\times10=20\ \mathrm V\]

Infinite parallel resistance does not interrupt the load’s current path.

المقاومة اللانهائية المتوازية لا تقطع مسار تيار الحمل.

2. Practical model with a finite parallel resistance

Let the internal resistance be \(90\,\Omega\), in parallel with the \(10\,\Omega\) load. The ideal \(2\,\mathrm{A}\) source current splits between these two branches.

2. نموذج حقيقي بمقاومة داخلية متوازية محدودة

نفترض أن المقاومة الداخلية \(90\,\Omega\) موصولة على التوازي مع الحمل \(10\,\Omega\). يتوزع تيار المنبع المثالي \(2\,\mathrm{A}\) بين هذين الفرعين.

\[I_L=I_s\frac{R_{\mathrm{int}}}{R_{\mathrm{int}}+R_L}=2\frac{90}{90+10}=\boxed{1.8\ \mathrm A}\]

The load voltage is also the voltage across the parallel internal resistance:

جهد الحمل هو نفسه الجهد بين طرفي المقاومة الداخلية المتوازية:

\[V=I_LR_L=1.8\times10=\boxed{18\ \mathrm V}\]
\[I_{\mathrm{int}}=\frac{V}{R_{\mathrm{int}}}=\frac{18}{90}=\boxed{0.2\ \mathrm A}\]

Check: the source current equals load current plus internal-branch current.

التحقق: تيار المنبع يساوي تيار الحمل مضافا إليه تيار الفرع الداخلي.

\[I_s=I_L+I_{\mathrm{int}}=1.8+0.2=2\ \mathrm A\]
Comparison: Iₛ = 2 A, Rₗ = 10 Ω | مقارنة عند تثبيت المنبع والحمل
Parallel internal resistance
المقاومة الداخلية المتوازية
Load current
تيار الحمل
Internal current
التيار الداخلي
90 Ω1.8 A0.2 A
990 Ω1.98 A0.02 A
→ ∞ (Ideal | مثالي)2 A0 A

3. Operating limits: maximum output voltage

As a separate example, consider a regulated source set to deliver \(2\,\mathrm{A}\), with a maximum output voltage of \(24\,\mathrm{V}\). Neglect internal leakage here to isolate the voltage-limit effect; this is not the preceding \(90\,\Omega\) model.

3. حدود التشغيل: أقصى جهد خرج

في مثال مستقل، نفترض منبع تيار منظما مضبوطا على \(2\,\mathrm{A}\)، لكنه يستطيع توليد جهد حتى \(24\,\mathrm{V}\) فقط. نهمل هنا التسرب الداخلي لتوضيح أثر حد الجهد وحده؛ فهذا ليس نموذج المقاومة \(90\,\Omega\) السابق.

  • With a \(10\,\Omega\) load, \(2\,\mathrm{A}\) requires \(20\,\mathrm{V}\), so current regulation is possible.
  • With a \(20\,\Omega\) load, \(2\,\mathrm{A}\) requires \(40\,\mathrm{V}\), which exceeds the source’s capability.
  • مع حمل \(10\,\Omega\)، يحتاج التيار \(2\,\mathrm{A}\) إلى جهد \(20\,\mathrm{V}\)، ولذلك يستطيع المنبع الحفاظ عليه.
  • مع حمل \(20\,\Omega\)، يحتاج التيار \(2\,\mathrm{A}\) إلى جهد \(40\,\mathrm{V}\)، وهذا يتجاوز قدرة المنبع.
\[V_{\mathrm{required}}=2\times20=40\ \mathrm V>24\ \mathrm V\]

If the device clamps its output at \(24\,\mathrm{V}\), the load current becomes:

إذا حد الجهاز جهد خرجه عند \(24\,\mathrm{V}\)، يصبح تيار الحمل:

\[I_L=\frac{24}{20}=\boxed{1.2\ \mathrm A}\]

The device may instead enter protection, depending on its design. The maximum load resistance permitting \(2\,\mathrm{A}\) under these assumptions is:

وقد يدخل الجهاز في الحماية بدلا من ذلك، بحسب تصميمه. وأكبر مقاومة حمل تسمح بتيار \(2\,\mathrm{A}\) وفق هذه الافتراضات هي:

\[R_{L,\max}=\frac{24}{2}=12\ \Omega\]

Voltage capability is an additional constraint; a parallel internal resistance alone does not describe it.

حد الجهد قيد إضافي، لا تصفه المقاومة الداخلية المتوازية وحدها.

Practical example: a \(12\,\mathrm{V}\), 30 Ah battery

مثال عملي: بطارية 12 فولت، 30 أمبير ساعي

\(12\,\mathrm{V}\) is the nominal voltage, not a guarantee of constant terminal voltage. 30 Ah is rated charge capacity under specified test conditions; it is neither a fixed output current nor the maximum permitted current. A battery is modelled as a practical voltage source, not a constant-current source.

\(12\,\mathrm{V}\) هو الجهد الاسمي، وليس ضمانا لثبات جهد الطرفين. و30 Ah هي سعة الشحنة الاسمية تحت شروط قياس محددة؛ لا تعني تيارا ثابتا ولا أقصى تيار مسموح. نمثل البطارية بمنبع جهد حقيقي، لا بمنبع تيار ثابت.

\[Q=30\ \mathrm{Ah}=30\times3600=\boxed{108\,000\ \mathrm C}\]
\[E_{\mathrm{nom}}\approx V_{\mathrm{nom}}Q_{\mathrm{Ah}}=12\times30=\boxed{360\ \mathrm{Wh}}\]

Here Ah measures charge, while Wh measures energy. Exact delivered energy depends on voltage throughout discharge: \(E=\int vi\,dt\). Some batteries sold in the “12 V” class have a nominal voltage of \(12.8\,\mathrm{V}\), giving 384 Wh at 30 Ah; use the actual datasheet value.

تقيس Ah الشحنة، بينما تقيس Wh الطاقة. تتوقف الطاقة الفعلية المسلمة على الجهد أثناء التفريغ: \(E=\int vi\,dt\). لبعض البطاريات المصنفة تجاريا «12 V» جهد اسمي \(12.8\,\mathrm{V}\)، فتكون طاقتها الاسمية 384 Wh عند 30 Ah؛ لذلك نعتمد القيمة الفعلية في المواصفات.

1. Supplying a 60 W load

Assume a direct DC load, constant \(12\,\mathrm{V}\), full usable rated capacity, and no conversion losses. These are teaching assumptions, not a runtime guarantee.

1. تشغيل حمل باستطاعة 60 W

نفترض حملا مستمرا مباشرا دون عاكس، وجهدا ثابتا \(12\,\mathrm{V}\)، وإمكانية استخدام كامل السعة الاسمية، ونهمل ضياعات التحويل. هذه فرضيات تعليمية وليست ضمانا لزمن التشغيل.

\[I=\frac{P}{V}=\frac{60}{12}=\boxed{5\ \mathrm A}\]
\[t_{\mathrm{ideal}}=\frac{30\ \mathrm{Ah}}{5\ \mathrm A}=\frac{360\ \mathrm{Wh}}{60\ \mathrm W}=\boxed{6\ \mathrm h}\]
Ideal estimates at 12 V | تقديرات مثالية عند 12 V
Load power | استطاعة الحملCurrent | التيارRuntime | زمن التشغيل
12 W1 A30 h
36 W3 A10 h
60 W5 A6 h
120 W10 A3 h

Actual runtime depends on chemistry, state of charge, aging, temperature, discharge rate, cutoff voltage, and losses. For example, if only 80% of the nominal energy is available to the load (an assumed teaching value), runtime at 60 W becomes:

يعتمد الزمن الفعلي على نوع البطارية وحالة شحنها وتقادمها ودرجة الحرارة ومعدل التفريغ وجهد الفصل والضياعات. مثلا، إذا كانت الطاقة المتاحة للحمل 80% فقط من الطاقة الاسمية، وهي نسبة مفترضة للتعليم، يصبح زمن تشغيل حمل 60 W:

\[t\approx\frac{360\times0.80}{60}=\boxed{4.8\ \mathrm h}\]

2. Capacity and C-rate do not specify the limit by themselves

For a 30 Ah battery, the following are arithmetic conversions only. A rate is permissible only if the manufacturer explicitly allows it, for the specified duration and conditions. Here C-rate is a rate designation; it is not the coulomb unit.

2. السعة ومعدل التفريغ لا يحددان الحد المسموح وحدهما

لبطارية 30 Ah، القيم التالية تحويلات حسابية فقط. لا يصبح أي معدل مسموحا إلا إذا أجازته الشركة للمدة والشروط المحددة. الرمز C في C-rate يدل على معدل التفريغ، وليس وحدة الكولوم.

Hypothetical rates for 30 Ah | معدلات افتراضية لسعة 30 Ah
C-rate | معدل التفريغCorresponding current | التيار المقابل
0.5C15 A
1C30 A
2C60 A
5C150 A

3. Comparison of two general battery models

The following values define two general teaching models with the same 30 Ah capacity and different current limits. They are illustrative model assumptions, not universal ratings or operating instructions for a particular battery.

3. مقارنة بين نموذجين عامين للبطارية

تحدد القيم التالية نموذجين عامين للتعليم بسعة واحدة 30 Ah وحدود تيار مختلفة. وهي افتراضات توضيحية للنموذجين، وليست حدودا عامة أو تعليمات تشغيل لبطارية بعينها.

Both have 30 Ah capacity; current limits differ | السعة 30 Ah لكليهما، وحدود التيار مختلفة
Model | الطرازVoltage | الجهدContinuous discharge | التفريغ المستمرPeak discharge and duration | التفريغ اللحظي ومدته
General Model 1 | النموذج الأول العام12 V nominal | اسمي30 A (1C)60 A / 5 s (2C)
Model 2 | النموذج الثاني12.8 V nominal | اسمي20 A (≈0.67C)100 A / 1 s (≈3.33C)

For Model 1, assume a continuous current ceiling of \(30\,\mathrm{A}\). For Model 2, the nominal continuous power is 256 W, calculated as \(12.8\times20\). Its \(100\,\mathrm{A}\) figure applies for one second only; it does not authorize sustained \(100\,\mathrm{A}\) operation or engine starting.

نفترض للنموذج الأول سقف تيار مستمر \(30\,\mathrm{A}\). وللنموذج الثاني نحسب الاستطاعة المستمرة الاسمية 256 W من العلاقة \(12.8\times20\). أما \(100\,\mathrm{A}\) فهي لمدة ثانية واحدة فقط؛ ولا تعني السماح بتيار مستمر \(100\,\mathrm{A}\) أو استخدام البطارية لتشغيل محرك احتراق.

4. Read the rating correctly

  • Continuous maximum: the upper sustained current under the stated conditions, not a promise of unlimited runtime.
  • Peak maximum: a short pulse with a stated duration; it cannot be treated as a continuous rating.
  • Charge current: a separate rating, not interchangeable with discharge current.
  • Short-circuit current: a fault current, not an allowed operating current. Do not test it by connecting the battery terminals together.

4. كيف نقرأ حدود التيار؟

  • الحد المستمر: أكبر تيار مستدام ضمن الشروط المحددة، ولا يعني زمنا غير محدود للتشغيل.
  • الحد اللحظي: نبضة قصيرة لمدة محددة، ولا يعامل كتيار مستمر.
  • تيار الشحن: له حد مستقل لا يساوي بالضرورة حد التفريغ.
  • تيار القصر: تيار عطل وليس تيارا مسموحا للتشغيل. لا يختبر بوصل قطبي البطارية مباشرة.

Check your understanding: Does 30 Ah guarantee \(30\,\mathrm{A}\) for one hour? No. One hour is the ideal arithmetic estimate; the model’s current limit and capacity test conditions must also permit that discharge. The \(20\,\mathrm{A}\) continuous Model 2 example already shows why the label alone is insufficient.

تحقق من فهمك: هل تضمن سعة 30 Ah إعطاء \(30\,\mathrm{A}\) لمدة ساعة؟ لا. الساعة نتيجة حسابية مثالية؛ ويجب أن تسمح حدود تيار الطراز وشروط قياس السعة بهذا التفريغ. ومثال النموذج الثاني ذي الحد المستمر \(20\,\mathrm{A}\) يوضح أن السعة وحدها لا تكفي.

From battery curves to a DC circuit model

من منحنيات البطارية إلى نموذج دارة التيار المستمر

The following drawings are schematic teaching illustrations, not measured curves for a specific battery or instructions for charger settings. They show the relationships between current, voltage and time.

الرسوم التالية توضيحية تعليمية، وليست منحنيات مقاسة لبطارية بعينها أو تعليمات لضبط الشاحن. هدفها بيان العلاقة بين التيار والجهد والزمن.

1. Discharge: voltage falls with time

Each curve assumes a different constant current. Follow it to the chosen cutoff line to estimate usable runtime. All three use the same illustrative \(11\,\mathrm{V}\) cutoff and a linear time axis.

1. التفريغ: انخفاض الجهد مع الزمن

يمثل كل منحنى تيارا ثابتا مختلفا. نتبعه حتى خط الفصل المختار لتقدير زمن التشغيل المفيد. نستخدم في الرسوم الثلاثة حد فصل افتراضيا واحدا \(11\,\mathrm{V}\) ومحور زمن خطيا.

Illustrative discharge curves at 3, 6 and 12 amperes with a common 11 volt cutoff10.51112130246810V | جهد الطرفينTime (h) | الزمن بالساعاتIllustrative cutoff 11 V | فصل افتراضي3 A6 A12 A
Illustrative curves, not battery specifications | منحنيات تخطيطية وليست مواصفات للبطارية

In this illustration, \(3\,\mathrm{A}\) reaches the cutoff at 8 h, \(6\,\mathrm{A}\) at 3.8 h, and \(12\,\mathrm{A}\) at 1.7 h. These assumed values demonstrate both a larger initial voltage drop and shorter operation at higher current. At \(6\,\mathrm{A}\):

في هذا الرسم الافتراضي يصل تيار \(3\,\mathrm{A}\) إلى الفصل بعد 8 h، و\(6\,\mathrm{A}\) بعد 3.8 h، و\(12\,\mathrm{A}\) بعد 1.7 h. توضح هذه القيم المفترضة زيادة هبوط الجهد الابتدائي وقصر زمن التشغيل عند زيادة التيار. عند \(6\,\mathrm{A}\):

\[Q_{\mathrm{out}}=I\,t=6\times3.8=22.8\ \mathrm{Ah}\]

For an assumed average discharge voltage of \(12\,\mathrm{V}\), the approximate delivered energy is:

إذا افترضنا أن متوسط جهد التفريغ \(12\,\mathrm{V}\)، فإن الطاقة المسلمة التقريبية:

\[E_{\mathrm{out}}\approx V_{\mathrm{avg}}It=12\times6\times3.8=273.6\ \mathrm{Wh}\]

The \(11\,\mathrm{V}\) line is an illustrative calculation threshold, not a recommended setting for every battery. A constant-power load such as an inverter draws increasing current as voltage falls, so a constant-current curve is only an approximation for that load.

خط \(11\,\mathrm{V}\) حد حسابي توضيحي، وليس إعدادا موصى به لكل بطارية. والحمل ثابت الاستطاعة، مثل العاكس، يسحب تيارا أكبر عندما ينخفض الجهد؛ لذلك لا يمثل منحنى التيار الثابت هذا الحمل بدقة تامة.

2. Charging and float: what happens in practice?

Read from left to right. Blue = battery-terminal voltage; red = current into the battery. The numbered stages align in both plots.

2. الشحن والتعويم: ماذا يحدث عمليا؟

اقرأ الرسم من اليسار إلى اليمين. الأزرق جهد طرفي البطارية، والأحمر التيار الداخل إليها. المراحل المرقمة متحاذية في الرسمين.

Charging voltage and battery current — جهد الشحن وتيار البطارية12314.413.812.030 VABattery current | تيار البطاريةTime → | الزمن
Illustrative 12 V lead-acid example; stage durations are not to scale.
مثال توضيحي لبطارية رصاص 12 V؛ عرض المرحلة لا يمثل مدتها الفعلية.
1. Charge the battery

The charger maintains an illustrative \(3\,\mathrm{A}\). The battery voltage rises from about \(12\,\mathrm{V}\) to \(14.4\,\mathrm{V}\).

1. شحن البطارية

يثبت الشاحن تيارا افتراضيا \(3\,\mathrm{A}\)، ويرتفع جهد البطارية تدريجيا من نحو \(12\,\mathrm{V}\) إلى \(14.4\,\mathrm{V}\).

2. Complete the charge

At \(14.4\,\mathrm{V}\), the charger holds voltage constant. Battery current gradually falls, for example from \(3\,\mathrm{A}\) toward a small value. Reaching \(14.4\,\mathrm{V}\) alone does not mean charging is complete.

2. إكمال الشحن

عند \(14.4\,\mathrm{V}\) يثبت الشاحن الجهد. يتناقص تيار البطارية تدريجيا، مثلا من \(3\,\mathrm{A}\) إلى قيمة صغيرة. وصول الجهد إلى \(14.4\,\mathrm{V}\) وحده لا يعني اكتمال الشحن.

3. Maintain charge: float

After the completion criteria are met, the charger lowers its target to an illustrative \(13.8\,\mathrm{V}\). The battery remains charged and draws a small maintenance current; this is not a fixed-current setting.

3. المحافظة على الشحن: التعويم

بعد تحقق شروط إكمال الشحن يخفض الشاحن جهد المحافظة، مثلا إلى \(13.8\,\mathrm{V}\). تبقى البطارية مشحونة وتسحب تيارا صغيرا للمحافظة على الشحن؛ وليس هذا ضبطا لتيار ثابت.

Why does the blue line drop? The charger changes its voltage target from \(14.4\,\mathrm{V}\) to \(13.8\,\mathrm{V}\). The battery has not suddenly emptied. The drawn transition is simplified; the actual voltage settles over time.

لماذا ينخفض الخط الأزرق؟ يغير الشاحن الجهد المستهدف من \(14.4\,\mathrm{V}\) إلى \(13.8\,\mathrm{V}\). لا يعني ذلك أن البطارية فرغت فجأة. الانتقال المرسوم مبسط؛ أما الجهد الفعلي فيستقر مع الزمن.

Practical purpose: a UPS ready for a power cut

While mains power is available, a UPS can supply its load and recharge its lead-acid battery. Once charging is complete, float keeps the battery ready by compensating for self-discharge, without continuously holding it at the higher absorption voltage.

When mains power fails, the battery discharges into the load. When power returns, the charger recharges it and later returns to float.

الفائدة العملية: بطارية UPS جاهزة لانقطاع الكهرباء

عند توفر الكهرباء يستطيع جهاز UPS تغذية الحمل وإعادة شحن بطاريته الرصاصية. وبعد اكتمال الشحن يحافظ التعويم على جاهزية البطارية بتعويض التفريغ الذاتي، دون إبقائها باستمرار عند جهد إكمال الشحن الأعلى.

عند انقطاع الكهرباء تفرغ البطارية طاقتها لتغذية الحمل. وعند عودة الكهرباء يعيد الشاحن شحنها، ثم يعود لاحقا إلى التعويم.

Why not keep \(14.4\,\mathrm{V}\) indefinitely? Holding a lead-acid battery at its absorption voltage for too long can cause overcharge and accelerate aging. Float uses a lower maintenance target. If the battery is charged and then disconnected for use, continuous float is not needed.

The red curve is battery current, not total charger current. With a connected load, the charger may supply substantial load current while only a small current enters the full battery.

لماذا لا نبقي الجهد عند \(14.4\,\mathrm{V}\) دائما؟ إطالة إبقاء بطارية الرصاص عند جهد إكمال الشحن قد تسبب الشحن الزائد وتسرع تقادمها. لذلك يستخدم التعويم جهدا أقل للمحافظة. أما إذا شحنا البطارية ثم فصلناها للاستخدام فلا نحتاج إلى تعويم مستمر.

الخط الأحمر يمثل تيار البطارية، وليس تيار الشاحن الكلي. مع وجود حمل قد يغذيه الشاحن بتيار كبير، بينما يدخل البطارية الممتلئة تيار صغير فقط.

Numerical illustration: if a load draws \(2\,\mathrm{A}\) and the full battery accepts \(0.1\,\mathrm{A}\), the charger supplies \(2.1\,\mathrm{A}\), neglecting losses. The \(0.1\,\mathrm{A}\) value is assumed, not a required float current.

مثال عددي: إذا سحب الحمل \(2\,\mathrm{A}\) وقبلت البطارية الممتلئة \(0.1\,\mathrm{A}\)، فإن الشاحن يزود \(2.1\,\mathrm{A}\) بإهمال الضياعات. قيمة \(0.1\,\mathrm{A}\) مفترضة، وليست تيار تعويم واجبا.

\[I_{\mathrm{charger}}=I_{\mathrm{load}}+I_{\mathrm{battery}}=2+0.1=2.1\ \mathrm A\]

Likewise, charging at \(3\,\mathrm{A}\) for 2 h passes 6 Ah into the battery, but not all of it is necessarily recoverable. The first stage illustrates current regulation; the next two illustrate voltage regulation.

Teaching values only: \(3\,\mathrm{A}\), \(14.4\,\mathrm{V}\) and \(13.8\,\mathrm{V}\) are assumed here. Actual charging voltage, temperature compensation and completion criteria depend on the battery specifications. The drawing does not specify charging settings for a particular battery.

وبالمثل، يمرر الشحن بتيار \(3\,\mathrm{A}\) لمدة 2 h شحنة 6 Ah إلى البطارية، لكنها ليست بالضرورة قابلة للاسترجاع كاملة. تبين المرحلة الأولى تنظيم التيار، وتبين المرحلتان التاليتان تنظيم الجهد.

قيم للتعليم فقط: افترضنا هنا \(3\,\mathrm{A}\) و\(14.4\,\mathrm{V}\) و\(13.8\,\mathrm{V}\). تعتمد قيم الشحن وتعويض الحرارة وشروط إنهاء الشحن على مواصفات البطارية. الرسم ليس تعليمات لضبط شاحن بطارية بعينها.

3. The battery model used in circuit analysis

During discharge, model the battery as an ideal emf E in series with an effective internal resistance r. Positive current leaves the positive terminal.

3. نموذج البطارية المستخدم في تحليل الدارات

أثناء التفريغ، نمثل البطارية بقوة محركة كهربائية مثالية E ومقاومة داخلية مكافئة r على التوالي. يخرج التيار الموجب من الطرف الموجب.

Battery equivalent circuit with series internal resistance and a six ohm load+−Er = 0.1 ΩIRL = 6 Ω+−VLBattery model | نموذج البطارية
\[I=\frac{E}{R_L+r},\qquad V_L=E-Ir\]

Illustrative values: E = \(12\,\mathrm{V}\), r = \(0.1\,\Omega\) and Rₗ = \(6\,\Omega\). The resistance is assumed for teaching, not measured from a particular battery.

قيم توضيحية: E = \(12\,\mathrm{V}\) وr = \(0.1\,\Omega\) وRₗ = \(6\,\Omega\). المقاومة الداخلية مفترضة للتعليم، وليست مقاسة من بطارية بعينها.

\[I=\frac{12}{6+0.1}\approx1.967\ \mathrm A,\qquad V_L=12-0.1I\approx11.803\ \mathrm V\]

Ignoring r gives \(2\,\mathrm{A}\) and \(12\,\mathrm{V}\). Relative to the model including r, the ideal-source approximation overestimates both by approximately 1.67% in this example.

During charging, if charging current is defined into the positive terminal, the simple resistive model gives:

عند إهمال r نحصل على \(2\,\mathrm{A}\) و\(12\,\mathrm{V}\). مقارنة بالنموذج الذي يتضمن r، يزيد تقريب المنبع المثالي القيمتين بنحو 1.67% في هذا المثال.

أثناء الشحن، إذا عرفنا تيار الشحن داخلا إلى الطرف الموجب، يعطينا النموذج المقاومي المبسط:

\[V_{\mathrm{terminal}}=E+I_{\mathrm{charge}}r\]

When is a fixed DC source suitable? For a short interval with little change in state of charge and temperature. Over a full discharge, E and effective r change, and this simple model does not capture polarization or all electrochemical dynamics. DC does not require a perfectly constant voltage.

متى يصلح تقريب المنبع المستمر الثابت؟ خلال فترة قصيرة لا تتغير فيها حالة الشحن ودرجة الحرارة كثيرا. أما على امتداد التفريغ فتتغير E والمقاومة المكافئة r، ولا يصف النموذج البسيط الاستقطاب وجميع الظواهر الكهروكيميائية. والتيار المستمر لا يشترط جهدا ثابتا تماما.

Source symbols and controlled sources | رموز المنابع والمنابع التابعة
An electrical circuit consists of interconnected elements. Passive elements such as resistors, capacitors and inductors do not generate energy; active elements such as voltage and current sources can supply energy. Whether a source supplies or absorbs power at a given instant depends on the circuit conditions.
تتكون الدارة الكهربائية من عناصر مترابطة. العناصر غير الفعالة مثل المقاومات والمكثفات والملفات لا تولد الطاقة، بينما العناصر الفعالة مثل منابع الجهد والتيار يمكنها تزويد الدارة بالطاقة. وقد يزود المصدر الاستطاعة أو يمتصها تبعا لشروط التشغيل.
Voltage source: imposes a specified terminal voltage, while the current depends on the connected circuit. An ideal independent voltage source maintains its prescribed voltage regardless of the current demanded.
منبع الجهد: يفرض فرق جهد محددا بين طرفيه، بينما يتحدد التيار وفق الدارة المتصلة به. يحافظ منبع الجهد المستقل المثالي على جهده المحدد بغض النظر عن التيار المطلوب.
\[v_s(t)=V_s\ \text{(DC)}\qquad\text{or}\qquad v_s(t)=f(t)\]
Current source: imposes a specified branch current, while the voltage across it depends on the circuit. An ideal independent current source maintains its prescribed current regardless of the terminal voltage.
منبع التيار: يفرض تيارا محددا في فرعه، بينما يتحدد الجهد بين طرفيه وفق الدارة. يحافظ منبع التيار المستقل المثالي على التيار المحدد بغض النظر عن الجهد بين طرفيه.
\[i_s(t)=I_s\ \text{(DC)}\qquad\text{or}\qquad i_s(t)=g(t)\]
Relationship between voltage and current: a source prescribes one quantity, but the other is set by the external network. For a resistor, Ohm’s law relates both quantities. Source power follows the chosen voltage polarity and current reference direction.
العلاقة بين الجهد والتيار: يحدد المصدر إحدى الكميتين بينما تتحدد الأخرى بحسب الشبكة الخارجية. أما في المقاومة فيربط قانون أوم بين الجهد والتيار. وتتحدد إشارة استطاعة المصدر بحسب قطبية الجهد واتجاه التيار المرجعي.
\[v_R=Ri_R\qquad p=vi\]
Independent sources: voltage or current is specified independently of other circuit variables. Dependent (controlled) sources: the source value is controlled by a voltage or current elsewhere in the circuit. A circle denotes an independent source; a diamond denotes a dependent source.
المصادر المستقلة: تحدد قيمة الجهد أو التيار بصورة مستقلة عن متغيرات الدارة الأخرى. المصادر التابعة (المتحكم بها): تتحدد قيمتها بجهد أو تيار في موضع آخر من الدارة. تمثل الدائرة المصدر المستقل، ويمثل المعين المصدر التابع.
+−+−Independent voltageمصدر جهد مستقلIndependent currentمصدر تيار مستقلDependent voltage(VCVS)مصدر جهد متحكم بهDependent current(VCCS)مصدر تيار متحكم بهVₛIₛVCVS: μvₓVCCS: gₘvₓ
Symbol correspondence: The two diamonds in the figure show VCVS (μvₓ) and VCCS (gₘvₓ). The other two controlled-source types, CCVS (rₘiₓ) and CCCS (βiₓ), use the same voltage-source diamond (+/−) and current-source diamond (arrow), respectively, but are controlled by current iₓ.
مطابقة الرموز: المعينان في الشكل يمثلان VCVS (μvₓ) وVCCS (gₘvₓ). أما النوعان الآخران CCVS (rₘiₓ) وCCCS (βiₓ) فيستخدمان رمز المعين مع قطبية الجهد (+/−) أو سهم التيار على الترتيب، لكن التحكم فيهما يتم بواسطة التيار iₓ.
The four controlled-source categories are: voltage-controlled voltage source (VCVS), current-controlled voltage source (CCVS), voltage-controlled current source (VCCS), and current-controlled current source (CCCS).
أنواع المصادر التابعة الأربعة هي: مصدر جهد متحكم به بجهد (VCVS)، ومصدر جهد متحكم به بتيار (CCVS)، ومصدر تيار متحكم به بجهد (VCCS)، ومصدر تيار متحكم به بتيار (CCCS).
\[\begin{aligned} \text{VCVS:}\quad v_s&=\mu v_x &\text{CCVS:}\quad v_s&=r_m i_x\\[8pt] \text{VCCS:}\quad i_s&=g_m v_x &\text{CCCS:}\quad i_s&=\beta i_x\end{aligned}\]
Here μ and β are dimensionless gains, rₘ is a transresistance (Ω), and gₘ is a transconductance (S). Ideal-source symbols represent mathematical models; physical sources have operating limits.
هنا μ وβ معاملا تكبير دون وحدة، وrₘ مقاومة تحويلية بوحدة الأوم، وgₘ ناقلية تحويلية بوحدة السيمنز. رموز المصادر المثالية نماذج رياضية، أما المصادر الحقيقية فلها حدود تشغيل.

9. Electrical power and energy

9. الاستطاعة والطاقة الكهربائية

Power is the rate of energy transfer, measured in watts (W). Energy is measured in joules (J) or watt-hours (Wh). With current referenced into the positive voltage terminal, absorbed power is:

الاستطاعة هي معدل انتقال الطاقة، وتقاس بالواط (W). أما الطاقة فتقاس بالجول (J) أو الواط ساعي (Wh). عندما نختار التيار داخلا من الطرف الموجب للجهد، تكون الاستطاعة الممتصة:

\[p(t)=v(t)i(t),\qquad \Delta E=\int_{t_1}^{t_2}p(t)\,dt\]
\[1\ \mathrm W=1\ \mathrm{J/s},\qquad 1\ \mathrm{Wh}=3600\ \mathrm J\]

Example: A load has \(12\,\mathrm{V}\) across it and draws \(2\,\mathrm{A}\) into its positive terminal. It absorbs 24 W. In 5 s it receives 120 J; in one hour it receives 24 Wh. Here the current is given; its calculation from resistance follows in the Ohm’s-law card.

مثال: حمل فرق الجهد بين طرفيه \(12\,\mathrm{V}\) ويدخل طرفه الموجب تيار \(2\,\mathrm{A}\)؛ يمتص استطاعة 24 W. وخلال 5 s يستقبل طاقة 120 J، وخلال ساعة يستقبل 24 Wh. التيار هنا معطى، وسنتعلم حسابه من المقاومة في بطاقة قانون أوم.

\[P=12\times2=24\ \mathrm W,\qquad \Delta E=P\Delta t=24\times5=120\ \mathrm J\]

10. Reference directions and the passive sign convention

10. الاتجاهات المرجعية واتفاقية إشارة المستقبل

Choose a voltage polarity and a current arrow before writing equations. Under the passive sign convention, the current arrow enters the terminal labelled +, so \(p=vi\) represents absorbed power.

  • \(p>0\): the element absorbs energy.
  • \(p<0\): the element supplies energy.

If the current reference enters the − terminal instead, absorbed power is \(-vi\).

نختار قطبية الجهد وسهم التيار قبل كتابة المعادلات. وفق اتفاقية إشارة المستقبل، يدخل سهم التيار من الطرف الموسوم +، فتكون \(p=vi\) هي الاستطاعة الممتصة.

  • إذا كان \(p>0\)، فالعنصر يمتص الطاقة.
  • إذا كان \(p<0\)، فالعنصر يزود الطاقة.

أما إذا دخل سهم التيار المرجعي من الطرف السالب، فإن الاستطاعة الممتصة تساوي \(-vi\).

i+−vp = vi

In the example, the load absorbs +24 W. Using current into the positive terminal as the reference for the source, the source current is −\(2\,\mathrm{A}\) and its absorbed power is −24 W. Thus total absorbed power is zero.

في المثال يمتص الحمل +24 W. وعند اختيار تيار المنبع المرجعي داخلا من طرفه الموجب تكون قيمته −\(2\,\mathrm{A}\)، فتكون استطاعته الممتصة −24 W. لذلك يكون مجموع الاستطاعات الممتصة صفرا.

\[p_{\mathrm{load}}+p_{\mathrm{source}}=24+(-24)=0\]

11. Scope and assumptions of this part

11. نطاق التحليل وافتراضاته

  • DC: unidirectional current; this part focuses on constant sources and steady-state values.
  • Steady state: the transient response following a switching event has ended.
  • Ideal wires: zero resistance, so directly connected points have the same potential.
  • Linear resistors: R is constant over the assumed operating range.
  • Lumped circuits: elements are described by terminal voltages and currents, neglecting propagation delays.

Nonlinear elements and transient responses require additional models and will be developed separately. Branches, nodes and loops are defined just before Kirchhoff’s laws.

  • التيار المستمر: تيار ذو اتجاه واحد؛ ونركز هنا على منابع ثابتة وقيم الحالة المستقرة.
  • الحالة المستقرة: تكون الاستجابة العابرة الناتجة عن التوصيل أو الفصل قد انتهت.
  • الأسلاك المثالية: مقاومتها صفر، ولذلك تتساوى كمونات النقاط المتصلة مباشرة بها.
  • المقاومات الخطية: تكون R ثابتة ضمن مجال التشغيل المفترض.
  • الدارات ذات العناصر المركزة: نمثل العناصر بجهودها وتياراتها الطرفية ونهمل تأخر انتشار الإشارات.

تحتاج العناصر غير الخطية والحالات العابرة نماذج إضافية تشرح لاحقا. أما الفروع والعقد والحلقات فنعرفها مباشرة قبل قانوني كيرشوف.

Historical dates indicate publication milestones or explicitly labelled periods. Modern notation and original teaching examples are used throughout; examples are not historical reconstructions. Gradual methods have no invented single birth year.
تشير التواريخ إلى محطات نشر أو حقب معلنة بوضوح. تُستخدم رموز حديثة وأمثلة تعليمية أصلية، وليست إعادة بناء لتجارب تاريخية. لا نضع سنة ولادة مخترعة للطرق التي تطورت تدريجيًا.
Scope: 12 historical teaching cards covering DC circuit analysis methods, including matrix formulation and modified nodal analysis (MNA). Some cards group related techniques: series/parallel reduction includes voltage/current division, and Kirchhoff’s laws include branch-current analysis. Thus the number of individual techniques is not necessarily 12. The focus is linear resistive steady-state circuits; nonlinear and transient DC circuits require additional tools.
النطاق: يضم هذا الجزء 12 بطاقة تعليمية مرتبة تاريخيًا لطرق تحليل دارات التيار المستمر، بما فيها الصياغة المصفوفية والتحليل العقدي المعدل (MNA). تجمع بعض البطاقات أساليب مترابطة؛ فتشمل بطاقة الاختزال تقسيم الجهد والتيار، وتشمل بطاقة قانوني كيرشوف تحليل تيارات الفروع. لذلك لا يلزم أن يساوي عدد الأساليب الفرعية عدد البطاقات. يركز الجزء على الدارات الخطية المقاومة في الحالة المستقرة، أما الدارات غير الخطية والعابرة فتحتاج أدوات إضافية.
1826–182701 · Ohm’s law
قانون أوم · 1826–1827
19th century · after 182702 · Series/parallel reduction; voltage/current division
اختزال التوالي والتوازي؛ تقسيم الجهد والتيار · القرن التاسع عشر بعد 1827
≈184003 · Maximum power transfer
نقل الاستطاعة العظمى · نحو 1840
184504 · Kirchhoff’s laws; branch-current method
قانونا كيرشوف؛ طريقة تيارات الفروع · 1845
184705 · Loop/mesh-current analysis
تحليل الحلقات والتيارات الحلقية · 1847
185306 · Superposition
التراكب أو التنضد · 1853
19th century · after Kirchhoff07 · Nodal analysis
تحليل العقد · القرن التاسع عشر بعد كيرشوف
188308 · Thévenin’s theorem
نظرية ثيفينن · 1883
189909 · Star–delta transformation
تحويل النجمة والمثلث · 1899
192610 · Mayer–Norton equivalent
مكافئ ماير–نورتن · 1926
after 192611 · Source transformation
تحويل المصادر · بعد 1926
197512 · Matrix solution and modified nodal analysis (MNA)
الحل المصفوفي والتحليل العقدي المعدل · 1975
1826–1827

Ohm’s law

قانون أوم

Published as a paper in 1826 and a monograph in 1827. The engineering need was a quantitative relation between current, voltage and conductor resistance.
نُشر في بحث عام 1826 وكتاب عام 1827. والحاجة الهندسية هي ربط التيار والجهد ومقاومة الناقل بعلاقة كمية.
Why use it / advantage: Direct calculation for an ohmic element.
الفائدة / الميزة: حساب مباشر للعنصر الأومي.
Limitation: Resistance must be appropriate to the operating conditions; a nonlinear element has no constant R.
القيد / العيب: يجب مراعاة ظروف التشغيل؛ العنصر غير الخطي لا يملك مقاومة ثابتة.

Worked example

مثال محلول بالتفصيل

A \(12\,\mathrm{V}\) source is connected across a \(6\,\Omega\) resistor. Find current and absorbed power.
مصدر \(12\,\mathrm{V}\) موصول على طرفي مقاومة \(6\,\Omega\). احسب التيار والاستطاعة الممتصة.
  1. Choose current from the positive terminal through the resistor.
    اختر اتجاه التيار من القطب الموجب عبر المقاومة.
    \[I=\frac{V_s}{R}=\frac{12}{6}=2\,\mathrm{A}\]
  2. Use the passive sign convention: current enters the positive voltage terminal.
    وفق اتفاقية المستهلك يدخل التيار الطرف الموجب للجهد.
    \[P=VI=12\times2=24\,\mathrm{W}\]
  3. Check using the resistance expression.
    تحقق باستخدام صيغة المقاومة.
    \[P=I^{2}R=2^{2}\times6=24\,\mathrm{W}\]
After 1827 · 19th century

Series/parallel reduction; voltage/current division

اختزال التوالي والتوازي؛ تقسيم الجهد والتيار

These are consequences of resistive circuit laws, developed through nineteenth-century practice. No separate invention date is assigned. Placement here is conceptual, not a claim of priority.
هذه نتائج لقوانين الدارات المقاومة تطورت ضمن ممارسة القرن 19، ولا تُنسب إلى سنة اختراع مستقلة. موضعها هنا يبيّن الأساس المفاهيمي ولا يدّعي أسبقية تاريخية.
Why use it / advantage: Fast reduction and convenient divider rules.
الفائدة / الميزة: اختزال سريع وقواعد مفيدة لتقسيم الجهد والتيار.
Limitation: Only true series or parallel connections qualify; a bridge cannot generally be reduced this way.
القيد / العيب: يجب تحقق التوالي أو التوازي فعليًا؛ لا تُختزل الدارة الجسرية عمومًا بهذه الطريقة.

Worked example

مثال محلول بالتفصيل

\(12\,\mathrm{V}\) across a \(2\,\Omega\) resistor in series with two parallel resistors, \(6\,\Omega\) and \(3\,\Omega\).
مصدر \(12\,\mathrm{V}\) يغذي مقاومة \(2\,\Omega\) على التوالي مع مقاومتين متوازيتين \(6\,\Omega\) و\(3\,\Omega\).
  1. Reduce the parallel pair; both resistors share exactly the same two nodes.
    اختزل الزوج المتوازي؛ للمقاومتين العقدتان نفسيهما.
    \[R_p=\frac{R_2R_3}{R_2+R_3}=\frac{6\times3}{6+3}=2\,\Omega\]
  2. Add the series resistance and find source current.
    اجمع مقاومتي التوالي واحسب تيار المصدر.
    \[\begin{aligned}R_{\mathrm{eq}}&=R_1+R_p=2+2=4\,\Omega\\[8pt]I_1&=\frac{V_s}{R_{\mathrm{eq}}}=\frac{12}{4}=3\,\mathrm{A}\end{aligned}\]
  3. Use voltage division to obtain the parallel-group voltage.
    استخدم تقسيم الجهد لحساب جهد مجموعة التوازي.
    \[V_p=V_s\frac{R_p}{R_1+R_p}=12\frac{2}{2+2}=6\,\mathrm{V}\]
  4. Obtain branch currents; check their sum. Current division gives the same answer.
    احسب تياري الفرعين وتحقق من جمعهما. يعطي تقسيم التيار النتيجة نفسها.
    \[\begin{aligned}I_2&=\frac{V_p}{R_2}=\frac{6}{6}=1\,\mathrm{A}\\[8pt]I_3&=\frac{V_p}{R_3}=\frac{6}{3}=2\,\mathrm{A}\\[8pt]I_1&=I_2+I_3=1+2=3\,\mathrm{A}\end{aligned}\]

General formulas for n resistors

العلاقات العامة لجمع n مقاومة على التسلسل والتفرع

Series connection: The same current passes through all resistors, and the equivalent resistance is their sum.
التوصيل على التسلسل: يمر التيار نفسه في جميع المقاومات، وتساوي المقاومة المكافئة مجموع قيم المقاومات.
\[\boxed{R_{\mathrm{eq,series}}=\sum_{i=1}^{n}R_i=R_1+R_2+\cdots+R_n}\]
Parallel connection: All resistors have the same voltage across them, and the reciprocal of the equivalent resistance equals the sum of the reciprocals.
التوصيل على التفرع (التوازي): يكون فرق الجهد نفسه على جميع المقاومات، ويساوي مقلوب المقاومة المكافئة مجموع مقلوبات قيم المقاومات.
\[\boxed{\frac{1}{R_{\mathrm{eq,parallel}}}=\sum_{i=1}^{n}\frac{1}{R_i}=\frac{1}{R_1}+\frac{1}{R_2}+\cdots+\frac{1}{R_n}}\]
\[\boxed{R_{\mathrm{eq,parallel}}=\left(\sum_{i=1}^{n}\frac{1}{R_i}\right)^{-1}}\]
≈1840 · approximate attribution

Maximum power transfer

نقل الاستطاعة العظمى

The maximum-power principle is often attributed to Moritz von Jacobi around 1840 (approximate date). For a real DC source with electromotive force E and fixed internal resistance r > 0, we determine the adjustable resistive load Rₗ that receives the greatest power. The analysis follows directly from Ohm’s law and differentiation.
تُنسب فكرة نقل الاستطاعة العظمى عادة إلى موريتس فون ياكوبي نحو عام 1840 (تاريخ تقريبي). ندرس مصدر تيار مستمر حقيقيا بقوة محركة كهربائية E ومقاومة داخلية ثابتة r > 0، ونحدد مقاومة الحمل المتغيرة Rₗ التي تستقبل أكبر استطاعة. يعتمد التحليل مباشرة على قانون أوم والاشتقاق.
Advantage: Identifies the load that receives maximum power from a fixed linear source. Limitation: Maximum power is not maximum efficiency: for the ideal series-resistance model, efficiency is 50% at the optimum.
الميزة: تحديد مقاومة الحمل التي تستقبل الاستطاعة العظمى من مصدر خطي ثابت. القيد: الاستطاعة العظمى لا تعني الكفاءة العظمى؛ تبلغ الكفاءة 50% عند المطابقة في النموذج المقاومي المثالي.

Theory and proof — real DC source

العلاقة النظرية والبرهان — مصدر مستمر حقيقي

Step-by-step derivation

اشتقاق العلاقة خطوة بخطوة

  1. Apply Kirchhoff’s voltage law around the source, internal resistance, and load. Solve for the current.
    طبق قانون كيرشوف للجهد على حلقة المصدر والمقاومة الداخلية والحمل، ثم استخرج التيار.
    \[\begin{aligned}E-I_Lr-I_LR_L&=0\\[8pt]E&=I_L(r+R_L)\\[8pt]I_L&=\frac{E}{r+R_L}\end{aligned}\]
  2. Write load power using Pₗ = Iₗ²Rₗ, then substitute the current expression.
    اكتب استطاعة الحمل من العلاقة Pₗ = Iₗ²Rₗ، ثم عوض التيار.
    \[\begin{aligned}P_L&=V_LI_L\\[8pt]V_L&=I_LR_L\\[8pt]P_L&=I_L^2R_L\\[8pt]&=\left(\frac{E}{r+R_L}\right)^2R_L\\[8pt]&=\frac{E^2R_L}{(r+R_L)^2}\end{aligned}\]
  3. Differentiate with respect to Rₗ. Treat E and r as constants and apply the product and chain rules.
    اشتق بالنسبة إلى Rₗ، مع اعتبار E وr ثابتين، واستخدام قاعدتي اشتقاق الجداء والدالة المركبة.
    \[\begin{aligned}P_L(R_L)&=E^2R_L(r+R_L)^{-2}\\[8pt]\frac{\mathrm dP_L}{\mathrm dR_L}&=E^2\frac{\mathrm d}{\mathrm dR_L}\!\left[R_L(r+R_L)^{-2}\right]\\[8pt]&=E^2\left[(r+R_L)^{-2}-2R_L(r+R_L)^{-3}\right]\\[8pt]&=E^2\frac{(r+R_L)-2R_L}{(r+R_L)^3}\\[8pt]&=\frac{E^2(r-R_L)}{(r+R_L)^3}\end{aligned}\]
  4. Find the stationary point. Set the derivative to zero. Since the denominator is positive for r > 0 and Rₗ ≥ 0, the numerator must vanish.
    أوجد النقطة الحرجة. ساو المشتقة بالصفر. بما أن المقام موجب عندما r > 0 وRₗ ≥ 0، فلا بد أن يكون البسط صفرا.
    \[\begin{aligned}\frac{\mathrm dP_L}{\mathrm dR_L}&=0\\[8pt]\frac{E^2(r-R_L)}{(r+R_L)^3}&=0\\[8pt]E^2(r-R_L)&=0\\[8pt]r-R_L&=0\quad(E\ne0)\\[8pt]\boxed{R_{L,\mathrm{opt}}=r}\end{aligned}\]
  5. Verify a maximum, not a minimum. First inspect the sign of the first derivative, then derive the second derivative step by step using the product and chain rules.
    تحقق أنها قيمة عظمى وليست صغرى. افحص إشارة المشتقة الأولى، ثم احسب المشتقة الثانية تفصيليًا باستخدام قاعدتي الجداء والسلسلة.
    \[\begin{aligned}R_L\lt r\quad&\Longrightarrow\quad \frac{\mathrm dP_L}{\mathrm dR_L}\gt0\\[8pt]R_L\gt r\quad&\Longrightarrow\quad \frac{\mathrm dP_L}{\mathrm dR_L}\lt0\end{aligned}\]
    Step A: Rewrite the first derivative as a product; E and r are constants.
    الخطوة أ: اكتب المشتقة الأولى بشكل جداء، مع اعتبار E وr ثابتين.
    \[\frac{\mathrm dP_L}{\mathrm dR_L}=E^2(r-R_L)(r+R_L)^{-3}\]
    Step B: Apply the product rule. The derivative of r − Rₗ is −1, and the chain rule gives −3(r + Rₗ)⁻⁴.
    الخطوة ب: طبق قاعدة اشتقاق الجداء. مشتقة r − Rₗ هي −1، وتعطي قاعدة السلسلة −3(r + Rₗ)⁻⁴.
    \[\begin{aligned}\frac{\mathrm d^2P_L}{\mathrm dR_L^2}&=E^2\frac{\mathrm d}{\mathrm dR_L}\left[(r-R_L)(r+R_L)^{-3}\right]\\[8pt]&=E^2\left[-(r+R_L)^{-3}-3(r-R_L)(r+R_L)^{-4}\right]\end{aligned}\]
    Step C: Use a common denominator and collect like terms.
    الخطوة ج: وحد المقامات واجمع الحدود المتشابهة.
    \[\begin{aligned}\frac{\mathrm d^2P_L}{\mathrm dR_L^2}&=E^2\frac{-(r+R_L)-3(r-R_L)}{(r+R_L)^4}\\[8pt]&=E^2\frac{-r-R_L-3r+3R_L}{(r+R_L)^4}\\[8pt]&=E^2\frac{(-r-3r)+(-R_L+3R_L)}{(r+R_L)^4}\\[8pt]&=E^2\frac{-4r+2R_L}{(r+R_L)^4}\\[8pt]&=E^2\frac{2(R_L-2r)}{(r+R_L)^4}\\[8pt]&=\frac{2E^2(R_L-2r)}{(r+R_L)^4}\end{aligned}\]
    Step D: Substitute Rₗ = r, simplify numerator and denominator, and verify that the result is negative for E ≠ 0 and r > 0.
    الخطوة د: عوض Rₗ = r، ثم بسط البسط والمقام وتحقق من سلبية النتيجة عندما E ≠ 0 وr > 0.
    \[\begin{aligned}\left.\frac{\mathrm d^2P_L}{\mathrm dR_L^2}\right|_{R_L=r}&=\frac{2E^2(r-2r)}{(r+r)^4}\\[8pt]&=-\frac{2E^2r}{16r^4}\\[8pt]&=\boxed{-\frac{E^2}{8r^3}\lt0}\end{aligned}\]
  6. Substitute the optimal load into the power formula and simplify.
    عوض مقاومة الحمل المثلى في معادلة الاستطاعة وبسط الناتج.
    \[\begin{aligned}P_{\max}&=\left.\frac{E^2R_L}{(r+R_L)^2}\right|_{R_L=r}\\[8pt]&=\frac{E^2r}{(r+r)^2}\\[8pt]&=\frac{E^2r}{4r^2}\\[8pt]&=\boxed{\frac{E^2}{4r}}\end{aligned}\]
\[E\ne 0,\qquad r>0,\qquad R_L\ge 0\]
The derivative is positive for loads below the internal resistance and negative for loads above it. Therefore, matching the load to the internal resistance maximizes load power. At this point, half the power supplied by the ideal voltage source is dissipated in the internal resistance.
تكون مشتقة الاستطاعة موجبة عندما تكون مقاومة الحمل أصغر من المقاومة الداخلية، وسالبة عندما تكون أكبر منها. لذلك تتحقق الاستطاعة العظمى عند تساوي المقاومتين. وعند هذه النقطة يتبدد نصف الاستطاعة التي يقدمها مصدر الجهد المثالي في المقاومة الداخلية.

Worked example — adjustable resistive load

مثال محلول — حمل مقاومي متغير

A real DC source has E = \(12\,\mathrm{V}\) and internal resistance r = \(3\,\Omega\). Find the optimal load and its maximum power.
مصدر مستمر حقيقي بقوة محركة E = \(12\,\mathrm{V}\) ومقاومة داخلية r = \(3\,\Omega\). أوجد الحمل الأمثل والاستطاعة العظمى.
r = 3 ΩRL (variable)12 VReal source → load | مصدر حقيقي ← حمل +− IL
  1. Write the current and load-power equations symbolically before substitution.
    اكتب معادلتي التيار واستطاعة الحمل بالرموز قبل التعويض.
    \[\begin{aligned}I_L&=\frac{E}{r+R_L}=\frac{12}{3+R_L}\\[8pt]P_L&=I_L^2R_L=\frac{E^2R_L}{(r+R_L)^2}=\frac{144R_L}{(3+R_L)^2}\end{aligned}\]
  2. Differentiate with respect to the load resistance and locate the maximum.
    اشتق بالنسبة إلى مقاومة الحمل وحدد نقطة الاستطاعة العظمى.
    \[\frac{\mathrm dP_L}{\mathrm dR_L}=\frac{E^2(r-R_L)}{(r+R_L)^3}=0\quad\Rightarrow\quad R_{L,\mathrm{opt}}=r=3\,\Omega\]
  3. Calculate current, maximum load power, and efficiency at matching.
    احسب التيار واستطاعة الحمل العظمى والكفاءة عند المطابقة.
    \[\begin{aligned}I_{L,\mathrm{opt}}&=\frac{12}{3+3}=2\,\mathrm A\\[8pt]P_{\max}&=I_{L,\mathrm{opt}}^2R_L=2^2\times3=12\,\mathrm W\\[8pt]\eta&=\frac{P_L}{P_L+I_L^2r}=\frac{12}{12+12}=50\%\end{aligned}\]
  4. Compare a non-optimal load \(R_L=6\,\Omega\).
    قارن بحمل غير أمثل \(R_L=6\,\Omega\).
    \[P_L(6\,\Omega)=\frac{12^2\times6}{(3+6)^2}=\frac{864}{81}\approx10.67\,\mathrm W<12\,\mathrm W\]

Interactive virtual experiment — change the load

تجربة افتراضية تفاعلية — غيّر مقاومة الحمل

I = \(2\,\mathrm{A}\); Pload = 12 W; efficiency = 50%
التيار = \(2\,\mathrm{A}\)؛ استطاعة الحمل = 12 W؛ الكفاءة = 50%
P (W)RL (Ω)0123918Pmax = 12 WRL = 3.0 Ω | 0.00 W

First derivative versus load resistance

منحنى المشتقة الأولى بدلالة مقاومة الحمل

\[\frac{\mathrm dP_L}{\mathrm dR_L}=\frac{E^2(r-R_L)}{(r+R_L)^3}=\frac{144(3-R_L)}{(3+R_L)^3}\]
P′ (W/Ω)03918RL (Ω) RL = 3.0 Ω | 0.00 W
Positive before \(3\,\Omega\): load power increases. Zero at \(3\,\Omega\): stationary maximum. Negative afterward: load power decreases. The orange marker follows the load slider.
قبل \(3\,\Omega\) تكون المشتقة موجبة فتزداد الاستطاعة، وتنعدم عند \(3\,\Omega\) حيث الاستطاعة العظمى، ثم تصبح سالبة فتتناقص الاستطاعة. تتبع النقطة البرتقالية منزلق الحمل.

Second derivative versus load resistance

منحنى المشتقة الثانية بدلالة مقاومة الحمل

\[\frac{\mathrm d^2P_L}{\mathrm dR_L^2}=\frac{2E^2(R_L-2r)}{(r+R_L)^4}=\frac{288(R_L-6)}{(R_L+3)^4}\]
P″ (W/Ω²)RL (Ω)036918 −25−15−5+5 Inflection / انعطاف RL = 3.0 Ω | 0.00 W
The second derivative is negative at the maximum-power point Rₗ = \(3\,\Omega\), crosses zero at Rₗ = \(6\,\Omega\) = 2r, and becomes positive afterward. The orange marker follows the same load slider.
تكون المشتقة الثانية سالبة عند الاستطاعة العظمى Rₗ = \(3\,\Omega\)، وتنعدم عند Rₗ = \(6\,\Omega\) = 2r، ثم تصبح موجبة. تتبع النقطة البرتقالية منزلق مقاومة الحمل نفسه.

Move the slider: the orange point follows the curve. At 3 Ω, power is highest. The plot is calculated from the source model, not measured data.

حرّك المنزلق: تتحرك النقطة البرتقالية على المنحنى. تبلغ الاستطاعة قيمتها العظمى عند 3 Ω. المنحنى محسوب من نموذج المصدر وليس قياسات فعلية.

Boundary cases: short circuit and open circuit

الحالتان الحديتان: القصر الكهربائي والدارة المفتوحة

Short circuit — \(R_L=0\). The load voltage and useful load power are zero, even though current is largest in this model. All electrical power supplied by the ideal source is dissipated in its internal resistance. Real sources may overheat or activate protection; never deliberately short a battery or supply.
القصر الكهربائي — \(R_L=0\). ينعدم جهد الحمل واستطاعته المفيدة رغم بلوغ التيار أكبر قيمة يسمح بها النموذج. تتبدد استطاعة المصدر في مقاومته الداخلية. قد يسخن المصدر الحقيقي أو تفصل الحماية؛ لا تجرّب قصر البطارية أو منبع التغذية عمليا.
\[\begin{aligned}I_{\mathrm{sc}}&=\left.\frac{E}{r+R_L}\right|_{R_L=0}=\frac Er\\[8pt]V_L&=I_{\mathrm{sc}}R_L=0\\[8pt]P_L&=I_{\mathrm{sc}}^2R_L=0\\[8pt]P_r&=I_{\mathrm{sc}}^2r=\frac{E^2}{r}\end{aligned}\]
Open circuit — \(R_L\to\infty\). Current and load power approach zero, while the load-terminal voltage approaches the source electromotive force. This is a limiting case, not a finite resistor value.
الدارة المفتوحة — \(R_L\to\infty\). يقترب التيار واستطاعة الحمل من الصفر، بينما يقترب جهد طرفي الحمل من القوة المحركة للمصدر. هذه حالة حدية وليست قيمة مقاومة منتهية.
\[\begin{aligned}\lim_{R_L\to\infty}I_L&=\lim_{R_L\to\infty}\frac{E}{r+R_L}=0\\[8pt]\lim_{R_L\to\infty}V_L&=\lim_{R_L\to\infty}\frac{ER_L}{r+R_L}=E\\[8pt]\lim_{R_L\to\infty}P_L&=\lim_{R_L\to\infty}\frac{E^2R_L}{(r+R_L)^2}=0\end{aligned}\]

Compare five important operating points

مقارنة خمس نقاط تشغيل مهمة

Case | الحالةR (Ω)I (A)V (V)P (W)P′ (W/Ω)P″ (W/Ω²)
Short circuit | قصر0 Ω4 A0 V0 W+16 W/Ω−21.333 W/Ω²
Maximum power | الاستطاعة العظمى3 Ω2 A6 V12 W0 W/Ω−0.667 W/Ω²
Inflection | انعطاف6 Ω1.333 A8 V10.667 W−0.593 W/Ω0 W/Ω²
Higher load | حمل أكبر12 Ω0.8 A9.6 V7.68 W−0.384 W/Ω+0.0341 W/Ω²
Open circuit limit | دارة مفتوحة∞0 A12 V0 W0 W/Ω0 W/Ω²

Values are rounded. The open-circuit row gives limits as load resistance tends to infinity.

القيم مقربة، وتمثل صفوف الدارة المفتوحة نهايات التوابع عندما تؤول مقاومة الحمل إلى اللانهاية.

Important: The slider illustrates finite loads from 0 to \(18\,\Omega\); its right endpoint is not an open circuit. The open-circuit point is the limit at infinity. Efficiency \(\eta=R_L/(r+R_L)\) approaches 100% as \(R_L\to\infty\), but useful power simultaneously approaches zero.
تنبيه: يوضح المنزلق مقاومات منتهية بين 0 و\(18\,\Omega\)؛ طرفه الأيمن ليس دارة مفتوحة. الدارة المفتوحة هي النهاية عند اللانهاية. تقترب الكفاءة \(\eta=R_L/(r+R_L)\) من 100% عندما \(R_L\to\infty\)، لكن الاستطاعة المفيدة تقترب في الوقت نفسه من الصفر.
1845

Kirchhoff’s laws; branch-current method

قانونا كيرشوف؛ طريقة تيارات الفروع

Kirchhoff formulated the junction-current and closed-loop voltage laws in 1845. These laws form the foundation of branch-current circuit analysis.
صاغ كيرشوف عام 1845 قانون تيارات العقد وقانون جهود الحلقات المغلقة. يشكل القانونان أساس طريقة تحليل تيارات الفروع.

Before solving: branches, nodes and loops

قبل الحل: الفروع والعقد والحلقات

A network is an interconnection of electrical elements. A branch represents a single two-terminal element, such as a resistor or an independent source. The diagram below has five branches: three resistors and two sources.
الشبكة الكهربائية هي مجموعة عناصر كهربائية مترابطة. الفرع يمثل عنصرا كهربائيا واحدا ذا طرفين، مثل مقاومة أو مصدر مستقل. تضم الدارة المرسومة خمسة فروع: ثلاث مقاومات ومصدرين.
Loop 1Loop 2Loop 3abc5 Ω2 Ω3 Ω10 V2 A
A node is a connection point between two or more branches. Points connected only by ideal wires form the same node, even if drawn at different positions. The example has three nodes, a, b and c.
العقدة هي نقطة اتصال فرعين أو أكثر. جميع النقاط المتصلة بأسلاك مثالية دون عناصر بينها تنتمي إلى العقدة نفسها حتى لو رسمت في مواضع مختلفة. تحوي الدارة ثلاث عقد: a وb وc.
A loop is any closed path that returns to its starting node without passing through a node more than once. An independent loop contains at least one branch absent from the other chosen independent loops.
الحلقة مسار مغلق يعود إلى عقدة البداية دون المرور بعقدة أكثر من مرة. أما الحلقة المستقلة فتحتوي على فرع واحد على الأقل لا يظهر في الحلقات المستقلة الأخرى المختارة.
For a connected network, the number of independent loops is l = b − n + 1, where b is the number of branches and n is the number of nodes. Here b = 5 and n = 3, so l = 3. The three dashed paths indicate the three independent mesh loops.
في شبكة متصلة يكون عدد الحلقات المستقلة l = b − n + 1 حيث b عدد الفروع وn عدد العقد. هنا b = 5 وn = 3، ومن ثم l = 3. المسارات الثلاثة المرسومة بخط متقطع تبين الحلقات الشبكية المستقلة الثلاث.
\[\boxed{l=b-n+1=5-3+1=3}\]
Series: two elements share an exclusive node and consequently carry the same current. Parallel: two elements connect to the same pair of nodes and consequently have the same voltage. Elements can also be neither series nor parallel.
التوالي: يشترك عنصران بعقدة لا يتصل بها فرع ثالث، ولذلك يمر فيهما التيار نفسه. التوازي: يتصل عنصران بالعقدتين نفسيهما، ولذلك يكون فرق الجهد بين طرفيهما متساويا. وقد لا يكون عنصران على التوالي ولا على التوازي.
In the illustrated network, the \(2\,\Omega\) and \(3\,\Omega\) resistors are in parallel, as are the \(3\,\Omega\) resistor and the current source. The \(10\,\mathrm{V}\) source and \(5\,\Omega\) resistor are in series through node a.
في الشبكة المرسومة، المقاومتان \(2\,\Omega\) و\(3\,\Omega\) على التوازي، وكذلك المقاومة \(3\,\Omega\) مع مصدر التيار. أما مصدر الجهد \(10\,\mathrm{V}\) والمقاومة \(5\,\Omega\) فهما على التوالي عبر العقدة a.
Next: Apply KCL at nodes and KVL around loops, then solve the unknown branch currents in the worked example below.
بعد هذه التعاريف: نطبق قانون كيرشوف للتيارات عند العقد وقانون الجهود على الحلقات، ثم نحل تيارات الفروع المجهولة في المثال التالي.
Kirchhoff’s Current Law (KCL): The algebraic sum of currents at any node is zero. Entering currents equal leaving currents.
قانون كيرشوف للتيارات: المجموع الجبري للتيارات عند أية عقدة يساوي الصفر، أي إن مجموع التيارات الداخلة يساوي الخارجة.
\[\boxed{\sum_{k=1}^{n} I_k=0}\qquad I_{\mathrm{in}}=I_{\mathrm{out}}\]
Kirchhoff’s Voltage Law (KVL): The algebraic sum of voltage rises and drops around a closed loop is zero.
قانون كيرشوف للجهود: المجموع الجبري لارتفاعات الجهد وهبوطاته حول أي مسار مغلق يساوي الصفر.
\[\boxed{\sum_{k=1}^{m} V_k=0}\]
Why use it / advantage: Works for general lumped DC circuits, even when simple series–parallel reduction is inconvenient.
الفائدة / الميزة: يصلح لتحليل الدارات المستمرة ذات العناصر المركزة، حتى عندما يصعب اختزالها بالتوالي والتوازي.
Limitation: Many branches produce many unknown currents and equations. Choose current directions consistently; a negative result means the real current flows opposite to the assumption.
القيد / العيب: يزداد عدد المجهولات والمعادلات بازدياد الفروع. يجب تثبيت الاتجاهات المفترضة؛ والإشارة السالبة تعني أن التيار الحقيقي يعاكس الاتجاه المفترض.

Worked example — three branch currents

مثال محلول — ثلاثة تيارات فروع

A \(12\,\mathrm{V}\) source supplies R₁ = \(4\,\Omega\) in series with two branches R₂ = \(6\,\Omega\) and R₃ = \(3\,\Omega\). At node A, I₁ enters; I₂ and I₃ leave. Node B is the \(0\,\mathrm{V}\) reference.
يغذي مصدر \(12\,\mathrm{V}\) المقاومة R₁ = \(4\,\Omega\) المتصلة على التوالي مع فرعين R₂ = \(6\,\Omega\) وR₃ = \(3\,\Omega\). يدخل التيار I₁ إلى العقدة A ويخرج منها I₂ وI₃. العقدة B هي مرجع الجهد الصفري.
  1. 1. Choose reference directions and write KCL at node A.
    1. حدد اتجاهات التيارات واكتب قانون التيارات عند العقدة A.
    \[I_1-I_2-I_3=0\quad\Longrightarrow\quad \boxed{I_1=I_2+I_3}\]
  2. 2. Apply KVL to the left loop (source, R₁, R₂). Traverse from the source positive terminal through the resistors.
    2. طبق قانون الجهود على الحلقة اليسرى التي تضم المصدر وR₁ وR₂، بدءا من القطب الموجب للمصدر.
    \[\begin{aligned}+E-R_1I_1-R_2I_2&=0\\[6pt]12-4I_1-6I_2&=0\\[6pt]\boxed{4I_1+6I_2=12}\end{aligned}\]
  3. 3. Apply KVL to the loop between the two parallel branches. Their voltage drops are equal.
    3. طبق قانون الجهود على الحلقة بين الفرعين المتوازيين؛ هبوط الجهد على المقاومتين متساو.
    \[\begin{gathered}+R_2I_2-R_3I_3=0\\[8pt]6I_2-3I_3=0\\[8pt]\boxed{I_3=2I_2}\end{gathered}\]
  4. 4. Substitute the second loop result into KCL to express all branch currents using I₂.
    4. عوض نتيجة الحلقة الثانية في قانون العقدة للتعبير عن جميع التيارات بدلالة I₂.
    \[\begin{gathered}I_1=I_2+I_3=I_2+2I_2\\[8pt]\boxed{I_1=3I_2}\end{gathered}\]
  5. 5. Solve the first loop equation step by step.
    5. حل معادلة الحلقة الأولى بالتعويض خطوة بخطوة.
    \[\begin{gathered}4(3I_2)+6I_2=12\\[8pt]12I_2+6I_2=12\\[8pt]18I_2=12\\[8pt]\boxed{I_2=\frac{2}{3}\ \mathrm A}\end{gathered}\]
  6. 6. Calculate the remaining branch currents and check KCL.
    6. احسب تياري الفرعين الباقيين وتحقق من قانون تيارات العقد.
    \[\begin{gathered}I_3=2I_2=2\cdot\frac23=\boxed{\frac43\ \mathrm A}\\[8pt]I_1=3I_2=3\cdot\frac23=\boxed{2\ \mathrm A}\\[8pt]I_2+I_3=\frac23+\frac43=2=I_1\end{gathered}\]
  7. 7. Verify KVL for both independent loops.
    7. تحقق من قانون الجهود في الحلقتين المستقلتين.
    \[\begin{gathered}12-4(2)-6\left(\frac23\right)=12-8-4=0\\[8pt]6\left(\frac23\right)-3\left(\frac43\right)=4-4=0\end{gathered}\]
  8. 8. Verify power conservation: source power equals total resistor dissipation.
    8. تحقق من توازن الاستطاعة: استطاعة المصدر تساوي مجموع الاستطاعات المبددة في المقاومات.
    \[\begin{gathered}P_{\mathrm{source}}=EI_1=12(2)=24\ \mathrm W\\[8pt]P_{R_1}=I_1^2R_1=2^2(4)=16\ \mathrm W\\[8pt]P_{R_2}=I_2^2R_2=\left(\frac23\right)^2(6)=\frac83\ \mathrm W\\[8pt]P_{R_3}=I_3^2R_3=\left(\frac43\right)^2(3)=\frac{16}{3}\ \mathrm W\\[8pt]16+\frac83+\frac{16}{3}=\boxed{24\ \mathrm W}\end{gathered}\]
Conclusion: I₁ = \(2\,\mathrm{A}\), I₂ = 2/\(3\,\mathrm{A}\), I₃ = 4/\(3\,\mathrm{A}\). All assumed current directions are correct because the results are positive.
النتيجة: I₁ = \(2\,\mathrm{A}\) وI₂ = 2/\(3\,\mathrm{A}\) وI₃ = 4/\(3\,\mathrm{A}\). جميع اتجاهات التيارات المفترضة صحيحة لأن النتائج موجبة.
1847 · systematic loop equations

Loop/mesh-current analysis

تحليل الحلقات والتيارات الحلقية

Kirchhoff’s 1847 graph-based work used meshes to solve circuit equations. Modern mesh analysis developed from this network approach; it should not be assigned an unsupported twentieth-century invention date.
استخدم عمل كيرشوف البياني عام 1847 الحلقات لحل معادلات الدارات. تطور التحليل الحلقي الحديث من هذا النهج ولا يصح منحه سنة اختراع حديثة بلا سند.
Why use it / advantage: Fewer unknowns for planar networks with few meshes.
الفائدة / الميزة: مجهولات أقل للشبكات المستوية قليلة الحلقات.
Limitation: Face-mesh analysis needs a planar graph; current sources may require a supermesh. General independent-loop analysis is broader.
القيد / العيب: تحليل الحلقات الوجهية يحتاج شبكة مستوية؛ قد تتطلب مصادر التيار حلقة فائقة. أما تحليل المسارات المغلقة المستقلة فأعم.
Face mesh (simple definition): Imagine drawing a circuit on paper without any wires crossing. Each smallest enclosed region between the wires is a face mesh: a closed path with no smaller loop inside it. A general closed loop may surround several such regions, so not every loop is a face mesh.
الحلقة الوجهية (تعريف مبسط): تخيل رسم الدارة على ورقة بحيث لا تتقاطع أسلاكها. كل منطقة مغلقة صغيرة تحيط بها الأسلاك، ولا توجد داخلها حلقة أصغر، تسمى حلقة وجهية. أما الحلقة المغلقة العامة فقد تحيط بعدة مناطق، لذلك ليست كل حلقة مغلقة حلقة وجهية.
Planar network: A network is planar if it can be drawn on a flat sheet without any branches crossing each other except at shared connection nodes. A crossing in one drawing does not by itself prove a network is nonplanar: a different layout may remove it.
الشبكة المستوية: هي شبكة يمكن رسم فروعها على سطح مستو دون تقاطع الفروع إلا عند العقد التي تتصل عندها كهربائيا. وجود تقاطع في رسم معين لا يعني بالضرورة أن الشبكة غير مستوية، فقد يمكن إعادة رسمها دون تقاطعات.
Mesh 1Mesh 2Outer loop = Mesh 1 + Mesh 2
Face meshes are the smallest bounded regions; the outer path surrounds both. | الحلقتان الوجهـيتان أصغر منطقتين مغلقتين، أما المسار الخارجي فيحيط بهما معا.
R1R2R3Planar network · No crossing branches
The connected branches meet at nodes, not at accidental crossings. | تتصل الفروع عند العقد ولا تتقاطع مع بعضها في مواضع غير مخصصة للاتصال.
Nonplanar network: A network is nonplanar when no rearrangement of its branches can eliminate every crossing between unconnected branches. The example below is K₃,₃: each of three left nodes connects to all three right nodes (nine branches). This graph is inherently nonplanar.
الشبكة غير المستوية: هي شبكة لا يمكن إعادة رسم فروعها على سطح مستو دون تقاطعات بين فروع غير متصلة كهربائيا. المثال التالي هو الشبكة K₃,₃، حيث تتصل كل عقدة من العقد الثلاث اليسرى بالعقد الثلاث اليمنى، أي يوجد 9 فروع. هذه الشبكة غير مستوية مهما أعدنا ترتيب رسمها.
ABC123K₃,₃ · 6 nodes · 9 branches
Nonplanar K₃,₃: unavoidable crossings, even after redrawing. | شبكة K₃,₃ غير مستوية، ولا يمكن إزالة جميع التقاطعات بإعادة الرسم.
Why the name K₃,₃? In graph theory, K denotes a complete graph (from the German word komplett). The subscript 3,3 indicates two groups of three nodes each. Every node in one group connects to all three nodes in the other group, but nodes within the same group do not connect. This is called a complete bipartite graph. In general, Kₘ,ₙ has m + n nodes and m × n branches.
لماذا تسمى K₃,₃؟ في نظرية المخططات، يشير الحرف K إلى الشبكة الكاملة، من كلمة komplett بالألمانية. يدل الرقمان 3 و3 على مجموعتين، في كل مجموعة ثلاث عقد. تتصل كل عقدة من المجموعة الأولى بالعقد الثلاث في المجموعة الثانية، ولا تتصل عقد المجموعة الواحدة ببعضها. تسمى هذه البنية الشبكة الثنائية الكاملة. عموما، تضم Kₘ,ₙ عدد m + n من العقد وعدد m × n من الفروع.
\[\boxed{K_{3,3}:\quad n=3+3=6,\qquad b=3\times3=9}\]
Important: Crossed lines in a particular diagram do not automatically imply nonplanarity; the crossings must be unavoidable in every planar drawing.
انتبه: تقاطع الخطوط في رسم واحد لا يعني بالضرورة أن الشبكة غير مستوية؛ المعيار هو استحالة التخلص من جميع التقاطعات عند إعادة الرسم.

Worked example

مثال محلول بالتفصيل

+−12 V4 Ω3 Ω6 Ωi1i2Ia = 2 A →Ic = 4/3 A →Ib = 2/3 A ↓
Mesh currents / تيارات الحلقات
Two clockwise meshes: left has a \(12\,\mathrm{V}\) rise and \(4\,\Omega\); right has \(3\,\Omega\); a shared \(6\,\Omega\) resistor carries \(i_1-i_2\) downward.
حلقتان باتجاه عقارب الساعة: اليسرى فيها ارتفاع جهد \(12\,\mathrm{V}\) ومقاومة \(4\,\Omega\)؛ اليمنى فيها \(3\,\Omega\)؛ المقاومة المشتركة \(6\,\Omega\) تحمل \(i_1-i_2\) نحو الأسفل.
  1. Apply KVL to the left mesh.
    طبّق قانون الجهد على الحلقة اليسرى.
    \[\begin{aligned}4i_1+6(i_1-i_2)&=12\\[8pt]10i_1-6i_2&=12\end{aligned}\]
  2. Apply KVL to the right mesh.
    طبّق قانون الجهد على الحلقة اليمنى.
    \[\begin{aligned}3i_2+6(i_2-i_1)&=0\\[8pt]-6i_1+9i_2&=0\end{aligned}\]
  3. Solve by substitution.
    حل بالتعويض.
    \[\begin{aligned}i_2&=\frac23i_1\\[8pt]10i_1-4i_1&=12\\[8pt]i_1&=2\,\mathrm A\\[8pt]i_2&=\frac43\,\mathrm A\end{aligned}\]
  4. Convert mesh currents to physical branch currents.
    حوّل تيارات الحلقات إلى تيارات الفروع الفعلية.
    \[\begin{aligned}I_a&=i_1=2\,\mathrm A\\[8pt]I_b&=i_1-i_2=\frac23\,\mathrm A\\[8pt]I_c&=i_2=\frac43\,\mathrm A\end{aligned}\]
Only three physical branch currents: \(I_a=i_1=2\,\mathrm{A}\) in the left branch (upward through the source and rightward through \(4\,\Omega\)); \(I_b=i_1-i_2=\frac{2}{3}\,\mathrm{A}\) downward through the shared \(6\,\Omega\) resistor; \(I_c=i_2=\frac{4}{3}\,\mathrm{A}\) in the right branch (rightward through \(3\,\Omega\), then downward along the wire). There are two mesh-current unknowns, not five independent currents. KCL at the top node: \(I_a=I_b+I_c=2\,\mathrm{A}\).
ثلاثة تيارات فروع فعلية فقط: \(I_a=i_1=2\,\mathrm{A}\) في الفرع الأيسر (صعودا عبر المنبع ثم يمينا عبر \(4\,\Omega\))، و\(I_b=i_1-i_2=\frac{2}{3}\,\mathrm{A}\) نحو الأسفل عبر المقاومة المشتركة \(6\,\Omega\)، و\(I_c=i_2=\frac{4}{3}\,\mathrm{A}\) في الفرع الأيمن (يمينا عبر \(3\,\Omega\) ثم نزولا عبر السلك). لدينا مجهولان فقط هما تيارا الحلقتين، وليست هناك خمسة تيارات مستقلة. قانون كيرشوف عند العقدة العليا: \(I_a=I_b+I_c=2\,\mathrm{A}\).
1853

Superposition

التراكب أو التنضد

Helmholtz’s 1853 paper reports superposition and a voltage-source equivalent. Linearity allows the separate contributions of independent sources to be added.
ورد التراكب والمكافئ الجهدي في عمل هلمهولتز عام 1853. تسمح الخطية بجمع المساهمات المنفردة للمصادر المستقلة.
Why use it / advantage: Reveals each source’s contribution.
الفائدة / الميزة: توضح مساهمة كل مصدر.
Limitation: Repeated solutions for many sources; powers do not add by superposition. Dependent sources remain active.
القيد / العيب: تتطلب حلولًا متكررة عند كثرة المصادر؛ ولا تُجمع الاستطاعات بالتراكب. تبقى المصادر التابعة فعالة.

General principle and solution procedure

المبدأ العام وخطوات تطبيق طريقة التراكب

Principle: In a linear circuit, the current through an element or the voltage across it equals the algebraic sum of the contributions produced by each independent source acting separately. Choose a fixed reference direction or polarity before calculating contributions.
المبدأ: في الدارة الخطية، يساوي تيار أي عنصر أو فرق الجهد عليه المجموع الجبري لمساهمات المنابع المستقلة عندما يعمل كل منبع على حدة. يجب تحديد اتجاه مرجعي للتيار أو قطبية مرجعية للجهد قبل الحساب.
\[\boxed{I=\sum_{k=1}^{m}I^{(k)},\qquad V=\sum_{k=1}^{m}V^{(k)}}\]
  1. Step 1: Select the required branch current or voltage and mark its positive reference direction or polarity.
    الخطوة 1: حدد تيار الفرع أو الجهد المطلوب، وارسم اتجاهه المرجعي الموجب أو قطبيته المرجعية.
  2. Step 2: Keep only one independent source active. Set the other independent sources to zero: replace an ideal voltage source by a short circuit and an ideal current source by an open circuit. Keep resistors and dependent sources in the circuit; retain internal resistance when a source is nonideal.
    الخطوة 2: أبق منبعا مستقلا واحدا فعالا. ألغ تأثير بقية المنابع المستقلة باستبدال منبع الجهد المثالي بقصر كهربائي، ومنبع التيار المثالي بدارة مفتوحة. أبق المقاومات والمنابع التابعة في الدارة، ولا تهمل المقاومة الداخلية للمنبع الحقيقي.
  3. Step 3: Calculate the contribution of the active source using Ohm's law, series/parallel reduction, or Kirchhoff's laws. Record the algebraic sign relative to the chosen reference.
    الخطوة 3: احسب مساهمة المنبع الفعال باستخدام قانون أوم أو اختزال التوالي والتفرع أو قوانين كيرشوف. احتفظ بالإشارة الجبرية بحسب الاتجاه المرجعي المختار.
  4. Step 4: Repeat for each remaining independent source, changing the active source each time while retaining the same reference direction.
    الخطوة 4: كرر الحساب مع كل منبع مستقل آخر، مع تثبيت الاتجاه المرجعي نفسه في جميع الحالات.
  5. Step 5: Add the signed current contributions or voltage contributions. If power is required, compute it from the total voltage and current; never sum the separately calculated powers.
    الخطوة 5: اجمع مساهمات التيار أو الجهد جمعا جبريا. إذا طلبت الاستطاعة فاحسبها من الجهد والتيار النهائيين، ولا تجمع الاستطاعات المحسوبة لكل منبع على حدة.
Important distinction: Superposition applies to linear voltage and current responses, but generally not directly to power because power depends on products or squares of those responses.
تنبيه مهم: يطبق التراكب على استجابات الجهد والتيار الخطية، ولا يطبق مباشرة على الاستطاعة لأنها تعتمد على جداء الجهد والتيار أو على مربعاتهما.

Worked example

مثال محلول بالتفصيل

+−12 V+−6 V6 Ω6 Ω6 ΩA0 V
Superposition circuit / دارة التراكب
Node A connects through three \(6\,\Omega\) resistors to +\(12\,\mathrm{V}\), +\(6\,\mathrm{V}\), and ground. Find downward current in the ground resistor.
العقدة A موصولة عبر ثلاث مقاومات \(6\,\Omega\) إلى +\(12\,\mathrm{V}\) و+\(6\,\mathrm{V}\) والمرجع. احسب التيار نحو الأسفل في مقاومة المرجع.
  1. Step 1 — Choose the requested response and its reference direction. In this circuit, we need the current through the vertical \(6\,\Omega\) resistor from node A to ground (downward). Call it \(I\). The bottom node is \(0\,\mathrm V\).
    الخطوة 1 — تحديد المطلوب واتجاهه المرجعي. نريد التيار المار في المقاومة العمودية \(6\,\Omega\) من العقدة A نحو المرجع (إلى الأسفل)، ونسميه \(I\). جهد العقدة السفلية \(0\,\mathrm V\).
    \[I=\frac{V_A}{6\,\Omega}\quad(\text{downward positive})\]
  2. Step 2 — Activate only the first independent source. Keep the \(12\,\mathrm V\) source active and replace the ideal \(6\,\mathrm V\) voltage source by a short circuit (zero voltage). The right-hand and vertical \(6\,\Omega\) resistors are then in parallel. Calculate the first contribution by voltage division, then Ohm's law.
    الخطوة 2 — تفعيل المنبع المستقل الأول فقط. أبق منبع \(12\,\mathrm V\) فعالا، واستبدل منبع الجهد المثالي \(6\,\mathrm V\) بقصر كهربائي لأن جهده يصبح صفرا. تصبح المقاومة اليمنى والمقاومة العمودية، وقيمة كل منهما \(6\,\Omega\)، على التوازي. احسب المساهمة الأولى بتقسيم الجهد ثم قانون أوم.
    \[\begin{aligned}R_p&=6\parallel6=3\,\Omega\\[8pt]V_A^{(12)}&=12\frac{3}{6+3}=4\,\mathrm V\\[8pt]I^{(12)}&=\frac{V_A^{(12)}}{6}=\frac46=\frac23\,\mathrm A\end{aligned}\]
  3. Step 3 — Repeat with the second independent source. Keep the \(6\,\mathrm V\) source active and replace the ideal \(12\,\mathrm V\) source by a short circuit. The left-hand and vertical resistors are now in parallel. Calculate the second contribution, using the same downward reference direction.
    الخطوة 3 — تكرار الحل للمنبع المستقل الثاني. أبق منبع \(6\,\mathrm V\) فعالا واستبدل منبع \(12\,\mathrm V\) المثالي بقصر كهربائي. تصبح المقاومة اليسرى والمقاومة العمودية على التوازي. احسب المساهمة الثانية مع الاحتفاظ بالاتجاه المرجعي نحو الأسفل.
    \[\begin{aligned}R_p&=6\parallel6=3\,\Omega\\[8pt]V_A^{(6)}&=6\frac3{6+3}=2\,\mathrm V\\[8pt]I^{(6)}&=\frac{V_A^{(6)}}6=\frac26=\frac13\,\mathrm A\end{aligned}\]
  4. Step 4 — Add the contributions algebraically. Both contributions are positive in the chosen downward direction, so they add. The node-voltage contributions add as well. Check that the total current equals the total node voltage divided by the vertical resistance.
    الخطوة 4 — جمع المساهمات جبريا. كلتا مساهمتي التيار موجبتان في الاتجاه المرجعي المختار نحو الأسفل، لذلك نجمعهما. ونجمع مساهمتي جهد العقدة أيضا. تحقق من أن التيار الكلي يساوي جهد العقدة الكلي مقسوما على المقاومة العمودية.
    \[\begin{aligned}V_A&=V_A^{(12)}+V_A^{(6)}=4+2=6\,\mathrm V\\[8pt]I&=I^{(12)}+I^{(6)}=\frac23+\frac13\\[8pt]&=\boxed{1\,\mathrm A}\\[8pt]I&=\frac{V_A}{6}=\frac66=1\,\mathrm A\end{aligned}\]
  5. Step 5 — Calculate power only after combining the responses. Use the total current through the vertical \(6\,\Omega\) resistor. The separate powers cannot simply be added because power is quadratic in current.
    الخطوة 5 — حساب الاستطاعة بعد جمع الاستجابات. استخدم التيار الكلي في المقاومة العمودية \(6\,\Omega\). لا يجوز جمع الاستطاعات المنفردة مباشرة لأن الاستطاعة تتناسب مع مربع التيار.
    \[\begin{aligned}P&=I^2R=(1)^2(6)=\boxed{6\,\mathrm W}\\[8pt]P^{(12)}+P^{(6)}&=\left(\frac23\right)^2 6+\left(\frac13\right)^2 6\\[8pt]&=\frac{10}{3}\,\mathrm W\ne6\,\mathrm W\end{aligned}\]
19th century · after Kirchhoff

Nodal analysis

تحليل العقد

Nodal analysis is a systematic use of KCL with node potentials, developed in nineteenth-century network theory. This card marks a period, not a single verified invention year. Its 1845 foundation has already been introduced.
تحليل العقد تنظيم لقانون التيار باستخدام جهود العقد، تطور ضمن نظرية الشبكات في القرن 19. البطاقة تحدد حقبة ولا تدعي سنة اختراع واحدة موثقة. وقد سبق عرض أساسه عام 1845.
Why use it / advantage: Usually only n − 1 node voltages; well suited to numerical assembly.
الفائدة / الميزة: غالبًا يحتاج n − 1 جهدًا عقديًا؛ مناسب لبناء المعادلات حاسوبيًا.
Limitation: A voltage source between unknown nodes needs an extra constraint and usually a supernode.
القيد / العيب: مصدر الجهد بين عقدتين مجهولتين يحتاج قيدًا إضافيًا وعادةً عقدة فائقة.

General nodal-analysis procedure

الخطوات العامة لطريقة جهود العقد

  1. Step 1 — Choose a reference node. Assign \(0\,\mathrm V\) to a convenient common node, usually the lower one.
    الخطوة 1 — اختيار العقدة المرجعية. اختر عقدة مشتركة مناسبة، وغالبا السفلية، واعتبر جهدها \(0\,\mathrm V\).
  2. Step 2 — Label unknown node voltages. Express every node voltage relative to the reference. A node connected to an ideal voltage source referenced to ground may already have a known voltage.
    الخطوة 2 — تسمية جهود العقد المجهولة. قس جهود العقد بالنسبة إلى المرجع. قد يكون جهد العقدة معلوما مباشرة إذا اتصلت بمنبع جهد مثالي مرجعه الأرضي.
  3. Step 3 — Apply Kirchhoff's current law (KCL). At each unknown-voltage node, choose currents leaving as positive. For a resistor between nodes \(a\) and \(b\), the current from \(a\) to \(b\) is \((V_a-V_b)/R\). Write the algebraic sum as zero.
    الخطوة 3 — تطبيق قانون كيرشوف للتيارات. عند كل عقدة مجهولة الجهد افترض التيارات الخارجة موجبة. التيار في مقاومة بين العقدتين \(a\) و\(b\)، من \(a\) إلى \(b\)، يساوي \((V_a-V_b)/R\). اجعل المجموع الجبري صفرا.
    \[\boxed{I_{a\to b}=\frac{V_a-V_b}{R},\qquad \sum I_{\mathrm{leaving}}=0}\]
  4. Step 4 — Solve the node-voltage equations. Combine fractions, simplify, and solve the resulting linear equation or system.
    الخطوة 4 — حل معادلات جهود العقد. وحد المقامات، ثم بسط المعادلات وحل المعادلة الخطية أو جملة المعادلات الناتجة.
  5. Step 5 — Find branch currents and verify KCL. Substitute the calculated voltages into Ohm's law and check that incoming and outgoing currents balance.
    الخطوة 5 — حساب تيارات الفروع والتحقق. عوض جهود العقد المحسوبة في قانون أوم، ثم تأكد أن مجموع التيارات الداخلة يساوي مجموع التيارات الخارجة.
Special case — supernode: If an ideal voltage source lies between two unknown-voltage nodes, enclose both in a supernode, apply KCL to its boundary and add the source-voltage constraint.
حالة خاصة — العقدة الفائقة: إذا وقع منبع جهد مثالي بين عقدتين مجهولتي الجهد، فاعتبرهما عقدة فائقة، وطبق قانون كيرشوف للتيارات على حدودها، مع إضافة معادلة فرق جهد المنبع.

Worked example

مثال محلول بالتفصيل

+−12 V4 Ω6 Ω3 ΩA0 V
Node-voltage circuit / دارة تحليل العقد
Use the same \(12\,\mathrm{V}\), \(4\,\Omega\), \(6\,\Omega\), \(3\,\Omega\) network introduced in 1845; ground is the common lower node.
استخدم شبكة \(12\,\mathrm{V}\) و\(4\,\Omega\) و\(6\,\Omega\) و\(3\,\Omega\) نفسها التي عُرضت في محطة 1845؛ العقدة السفلى المشتركة هي المرجع.
  1. Step 1 — Reference node: Take the common lower conductor as ground, \(V_{\mathrm{ref}}=0\,\mathrm V\).
    الخطوة 1 — العقدة المرجعية: اختر الموصل السفلي المشترك مرجعا، بحيث \(V_{\mathrm{ref}}=0\,\mathrm V\).
  2. Step 2 — Node voltages: The source fixes its upper terminal at \(12\,\mathrm V\). Let \(V_A\) be the only unknown node voltage at A.
    الخطوة 2 — جهود العقد: يثبت المنبع جهد طرفه العلوي عند \(12\,\mathrm V\)، ويبقى جهد العقدة A، أي \(V_A\)، المجهول الوحيد.
  3. Step 3 — KCL at A: Express the currents leaving A toward the source terminal and through the \(6\,\Omega\) and \(3\,\Omega\) resistors. Their algebraic sum equals zero.
    الخطوة 3 — قانون التيارات عند A: اكتب التيارات الخارجة من A نحو طرف المنبع وعبر المقاومتين \(6\,\Omega\) و\(3\,\Omega\)، واجعل مجموعها الجبري صفرا.
    \[\frac{V_A-12}{4}+\frac{V_A}{6}+\frac{V_A}{3}=0\]
  4. Step 4 — Solve: Multiply by the least common denominator \(12\), collect terms and calculate the node voltage.
    الخطوة 4 — الحل: اضرب بطرفي المعادلة بالمضاعف المشترك الأصغر \(12\)، ثم اجمع الحدود واحسب جهد العقدة.
    \[\begin{aligned}3(V_A-12)+2V_A+4V_A&=0\\[8pt]9V_A-36&=0\\[8pt]\boxed{V_A=4\,\mathrm V}\end{aligned}\]
  5. Step 5 — Branch currents and verification: The \(4\,\Omega\) branch supplies node A; the other currents leave A toward ground. Verify their balance.
    الخطوة 5 — تيارات الفروع والتحقق: يغذي فرع \(4\,\Omega\) العقدة A، بينما يغادرها تيارا الفرعين الآخرين باتجاه المرجع. تحقق من توازن التيارات.
    \[\begin{aligned}I_1&=\frac{12-4}{4}=2\,\mathrm A\\[8pt]I_2&=\frac46=\frac23\,\mathrm A\\[8pt]I_3&=\frac43\,\mathrm A\\[8pt]\boxed{I_1=I_2+I_3=2\,\mathrm A}\end{aligned}\]

Supernode — definition and worked example

العقدة الفائقة — التعريف والمثال المحلول

A supernode combines two non-reference nodes joined by an ideal voltage source. Apply KCL to the boundary of the combined region, then use the source voltage as a second equation. Here the voltage source has its positive terminal at A.
العقدة الفائقة هي عقدتان غير مرجعيتين بينهما منبع جهد مثالي. نطبق قانون التيارات على حدود المنطقة التي تضمهما، ثم نضيف قيد جهد المنبع معادلة ثانية. في هذا المثال قطب منبع الجهد الموجب عند A.
+−4 V3 AABSupernodeReference node: 0 V 2 Ω2 Ω I1I2
Supernode circuit and current directions / دارة العقدة الفائقة واتجاهات التيارات
  1. Step 1 — Reference: The entire lower wire is the reference node at \(0\,\mathrm V\).
    الخطوة 1 — المرجع: السلك السفلي كله عقدة مرجعية جهدها \(0\,\mathrm V\).
    \[V_{\mathrm{ref}}=0\,\mathrm V\]
  2. Step 2 — Voltage constraint: The \(4\,\mathrm V\) source is positive at A, so A is \(4\,\mathrm V\) above B.
    الخطوة 2 — قيد الجهد: القطب الموجب لمنبع \(4\,\mathrm V\) عند A، لذلك يزيد جهد A على جهد B بمقدار \(4\,\mathrm V\).
    \[\boxed{V_A-V_B=4\,\mathrm V}\]
  3. Step 3 — KCL: Enclose A, B and the source in one supernode. The \(3\,\mathrm A\) source enters; the two resistor currents leave. The current inside the ideal voltage source does not cross the supernode boundary.
    الخطوة 3 — قانون كيرشوف للتيارات: أحط العقدتين A وB ومنبع الجهد بعقدة فائقة. يدخل إليها تيار \(3\,\mathrm A\) ويخرج عبر المقاومتين. تيار منبع الجهد الداخلي لا يعبر حدود العقدة الفائقة.
    \[\begin{aligned}\frac{V_A}{2}+\frac{V_B}{2}&=3\\[8pt]V_A+V_B&=6\,\mathrm V\end{aligned}\]
  4. Step 4 — Solve: Combine the KCL equation with the voltage-source constraint.
    الخطوة 4 — الحل: حل معادلة التيارات مع قيد منبع الجهد.
    \[\begin{aligned}V_A+V_B&=6\\[8pt]V_A-V_B&=4\\[8pt]2V_A&=10\\[8pt]\boxed{V_A=5\,\mathrm V}\\[8pt]\boxed{V_B=1\,\mathrm V}\end{aligned}\]
  5. Step 5 — Verify: Calculate downward branch currents with Ohm's law, then confirm current balance at the supernode boundary.
    الخطوة 5 — التحقق: احسب تياري المقاومتين باتجاه الأسفل بقانون أوم، ثم تحقق من توازن التيارات على حدود العقدة الفائقة.
    \[\begin{aligned}I_1&=\frac{V_A}{2\,\Omega}=2.5\,\mathrm A\\[8pt]I_2&=\frac{V_B}{2\,\Omega}=0.5\,\mathrm A\\[8pt]\boxed{I_1+I_2=3\,\mathrm A}\end{aligned}\]
1883 · earlier foundation: 1853

Thévenin’s theorem

نظرية ثيفينن

Thévenin published the voltage-source equivalent in 1883, independently of Helmholtz’s earlier 1853 result. The engineering benefit is a compact terminal model for changing loads.
نشر ثيفينن المكافئ الجهدي عام 1883 مستقلًا عن نتيجة هلمهولتز السابقة عام 1853. والفائدة الهندسية نموذج مختصر لطرفي الحمل عند تغييره.
Why use it / advantage: One equivalent can serve many load calculations.
الفائدة / الميزة: مكافئ واحد لحساب عدة أحمال.
Limitation: Describes terminal behavior, not every internal branch. With dependent sources use a test source or another valid resistance calculation.
القيد / العيب: يصف سلوك الطرفين ولا يحدد جميع الفروع الداخلية. مع المصادر التابعة يُستخدم مصدر اختبار أو طريقة صحيحة أخرى لحساب المقاومة.

Steps of Thévenin’s method

For a linear two-terminal circuit, replace the network seen from the load terminals by an ideal voltage source \(V_{\mathrm{Th}}\) in series with a resistance \(R_{\mathrm{Th}}\). Follow these steps in order:

خطوات تطبيق طريقة ثيفينن

في الدارات الخطية ذات الطرفين، نستبدل الشبكة كما يراها الحمل بمنبع جهد مثالي \(V_{\mathrm{Th}}\) على التسلسل مع مقاومة \(R_{\mathrm{Th}}\). نتبع الخطوات الآتية بالترتيب:

  1. Identify the load and terminals: Label the load terminals A and B, then temporarily disconnect the load \(R_L\). Keep the rest of the circuit unchanged.
    تحديد الحمل والطرفين: نحدد طرفي الحمل A وB، ثم نفصل مقاومة الحمل \(R_L\) مؤقتا، مع إبقاء بقية الدارة دون تغيير.
  2. Calculate the open-circuit voltage: With the load disconnected, determine the voltage between A and B using a suitable circuit-analysis method. This is the Thévenin voltage (polarity from A to B).
    حساب جهد الدارة المفتوحة: بعد فصل الحمل، نحسب فرق الجهد بين A وB بطريقة تحليل مناسبة. وهو جهد ثيفينن، وفق القطبية المحددة من A إلى B.
    \[V_{\mathrm{Th}}=V_{\mathrm{OC}}=V_A-V_B\]
  3. Calculate the equivalent resistance: In circuits with independent sources only, set independent ideal voltage sources to zero (replace by short circuits) and independent ideal current sources to zero (replace by open circuits). Find the resistance seen looking into A–B. Keep any dependent sources active; in their presence a test source can be used.
    حساب المقاومة المكافئة: إذا احتوت الدارة على منابع مستقلة فقط، نصفر منابع الجهد المثالية المستقلة باستبدالها بقصر كهربائي، ونصفر منابع التيار المثالية المستقلة باستبدالها بدارة مفتوحة. ثم نحسب المقاومة التي نراها من الطرفين A وB. أما المنابع التابعة فتبقى فعالة، ويمكن استخدام منبع اختبار لحساب المقاومة.
    \[R_{\mathrm{Th}}=R_{\mathrm{eq},AB}\]
  4. Draw the Thévenin equivalent: Replace the original network, as seen from A–B, with \(V_{\mathrm{Th}}\) in series with \(R_{\mathrm{Th}}\), then reconnect \(R_L\).
    رسم دارة ثيفينن المكافئة: نستبدل الشبكة الأصلية، كما تظهر من A وB، بمنبع الجهد \(V_{\mathrm{Th}}\) والمقاومة \(R_{\mathrm{Th}}\) على التسلسل، ثم نعيد توصيل الحمل \(R_L\).
  5. Compute and verify: Use Ohm’s law to find load current and voltage, respecting the chosen polarity and current direction. Compare with the original circuit when useful.
    الحساب والتحقق: نطبق قانون أوم لحساب تيار الحمل وجهده مع مراعاة القطبية واتجاه التيار المفترضين. ويمكن مقارنة النتيجة بحل الدارة الأصلية للتحقق.
    \[I_L=\frac{V_{\mathrm{Th}}}{R_{\mathrm{Th}}+R_L},\qquad V_L=I_L R_L\]

Important: The load must be disconnected when calculating \(V_{\mathrm{Th}}\) and \(R_{\mathrm{Th}}\); a short circuit replaces an independent ideal voltage source only during the resistance calculation, not during the open-circuit voltage calculation.

تنبيه: نفصل الحمل أثناء حساب كل من \(V_{\mathrm{Th}}\) و\(R_{\mathrm{Th}}\). ولا نستبدل منبع الجهد المستقل المثالي بقصر كهربائي إلا عند حساب المقاومة المكافئة، وليس عند حساب جهد الدارة المفتوحة.

Worked example

مثال محلول بالتفصيل

+−12 V4 Ω6 Ω3 ΩABRL = 3 Ω
Thévenin and load / ثيفينين والحمل
\(12\,\mathrm{V}\) source → \(4\,\Omega\) → terminal A; \(6\,\Omega\) connects A to ground B. A load RL = \(3\,\Omega\) will connect across A–B.
مصدر \(12\,\mathrm{V}\) ثم \(4\,\Omega\) ثم الطرف A؛ مقاومة \(6\,\Omega\) بين A والمرجع B. يُوصل حمل RL = \(3\,\Omega\) بين A وB.
  1. Remove only the load. Calculate the open-circuit terminal voltage.
    افصل الحمل فقط واحسب جهد الدارة المفتوحة على الطرفين.
    \[V_{\mathrm{Th}}=12\frac6{4+6}=7.2\,\mathrm V\]
  2. Deactivate the independent voltage source by shorting it; look into A–B.
    عطل مصدر الجهد المستقل بقصره وانظر إلى الشبكة من A وB.
    \[R_{\mathrm{Th}}=4\parallel6=\frac{24}{10}=2.4\,\Omega\]
  3. Reconnect the load to the equivalent.
    أعد توصيل الحمل بالمكافئ.
    \[\begin{aligned}I_L&=\frac{7.2}{2.4+3}=\frac43\,\mathrm A\\[8pt]V_L&=I_L(3)=4\,\mathrm V\end{aligned}\]
  4. Change the load without re-solving the internal network.
    غيّر الحمل دون إعادة حل الشبكة الداخلية.
    \[\begin{aligned}R_L&=6\,\Omega\\[8pt]I_L&=\frac{7.2}{8.4}=\frac67\,\mathrm A\\[8pt]V_L&=\frac{36}7\,\mathrm V\end{aligned}\]

Worked example 2 — Thévenin with a dependent source

المثال المحلول الثاني — ثيفينن بوجود منبع تابع

Given: An independent \(10\,\mathrm{V}\) voltage source, a \(4\,\Omega\) resistor, a dependent current source directed from A to B with \(I_d=\alpha V_A\), \(\alpha=0.2\,\mathrm{S}\), and a \(5\,\Omega\) load. Node B is the reference (\(V_B=0\)). Find the Thévenin equivalent seen at A–B and verify the load current.

المعطيات: منبع جهد مستقل \(10\,\mathrm{V}\)، ومقاومة \(4\,\Omega\)، ومنبع تيار تابع متجه من A إلى B وقيمته \(I_d=\alpha V_A\)، حيث \(\alpha=0.2\,\mathrm{S}\)، وحمل مقاومته \(5\,\Omega\). العقدة B مرجع الجهد (\(V_B=0\)). المطلوب مكافئ ثيفينن بين A وB والتحقق من تيار الحمل.

+−10 V4 ΩId = αVAα = 0.2 SAB5 ΩRLIL ↓
Original network / الدارة الأصلية

Step 1 — Disconnect the load and calculate the open-circuit voltage

Remove only \(R_L\). Leave the independent and dependent sources active. Apply Kirchhoff’s current law at A, taking currents leaving A as positive.

الخطوة 1 — فصل الحمل وحساب جهد الدارة المفتوحة

نفصل \(R_L\) فقط، ونبقي المنبعين المستقل والتابع فعالين. نطبق قانون كيرشوف للتيارات عند العقدة A، ونعد التيارات الخارجة منها موجبة.

+−10 V4 ΩId = αVAα = 0.2 SABOpen / مفتوحVOC = VA
Load disconnected; all sources active / فصل الحمل مع إبقاء المنابع فعالة
\[\frac{V_A-10}{4}+0.2V_A=0\]
\[V_A-10+0.8V_A=0\quad\Longrightarrow\quad 1.8V_A=10\]
\[\boxed{V_{\mathrm{Th}}=V_{\mathrm{OC}}=V_A=\frac{50}{9}\,\mathrm V\approx5.56\,\mathrm V}\]

Step 2 — Determine the Thévenin resistance using a test source

Keep the load disconnected. Set the independent ideal \(10\,\mathrm V\) source to zero (a short circuit), but do not deactivate the dependent current source. Connect a \(1\,\mathrm V\) test voltage source across A–B, with positive terminal at A. Define \(I_{\mathrm{test}}\) as the current entering the network from that test source.

الخطوة 2 — حساب مقاومة ثيفينن باستخدام منبع اختبار

يبقى الحمل مفصولا. نصفر منبع الجهد المثالي المستقل \(10\,\mathrm V\) باستبداله بقصر كهربائي، ولا نصفر منبع التيار التابع. نصل منبع جهد اختبار \(1\,\mathrm V\) بين A وB بقطبه الموجب عند A، ونعرف \(I_{\mathrm{test}}\) بأنه التيار الداخل إلى الشبكة من منبع الاختبار.

10 V → short4 ΩId = αVAα = 0.2 SAB+−1 VItest →Test source / منبع اختبار
Independent voltage source shorted; dependent source active / قصر المنبع المستقل وإبقاء المنبع التابع
\[I_{\mathrm{test}}=\frac{V_{\mathrm{test}}}{4\,\Omega}+\alpha V_{\mathrm{test}}\]
\[V_{\mathrm{test}}=1\,\mathrm V\;\Longrightarrow\;I_{\mathrm{test}}=0.25\,\mathrm A+0.20\,\mathrm A=0.45\,\mathrm A\]
\[\boxed{R_{\mathrm{Th}}=\frac{V_{\mathrm{test}}}{I_{\mathrm{test}}}=\frac{1}{0.45}=\frac{20}{9}\,\Omega\approx2.22\,\Omega}\]

Step 3 — Draw the equivalent circuit and reconnect the load

Replace the network to the left of A–B by \(V_{\mathrm{Th}}\) in series with \(R_{\mathrm{Th}}\). Reconnect \(R_L=5\,\Omega\).

الخطوة 3 — رسم الدارة المكافئة وإعادة توصيل الحمل

نستبدل الشبكة التي يراها الطرفان A وB بمنبع \(V_{\mathrm{Th}}\) ومقاومة \(R_{\mathrm{Th}}\) على التسلسل، ثم نعيد وصل \(R_L=5\,\Omega\).

+−5.56 V2.22 Ω5 ΩABRLIL = 10/13 A →VL = 50/13 V
Equivalent source and resistor with reconnected load / دارة ثيفينن المكافئة مع الحمل
\[I_L=\frac{V_{\mathrm{Th}}}{R_{\mathrm{Th}}+R_L}=\frac{50/9}{20/9+5}=\boxed{\frac{10}{13}\,\mathrm A\approx0.769\,\mathrm A}\]
\[V_L=I_LR_L=\boxed{\frac{50}{13}\,\mathrm V\approx3.85\,\mathrm V}\]

Step 4 — Verify directly in the original circuit

Apply KCL at A with the load connected. The result must agree with the Thévenin equivalent.

الخطوة 4 — التحقق مباشرة من الدارة الأصلية

نطبق قانون كيرشوف للتيارات عند A بعد إعادة توصيل الحمل، ونقارن النتيجة بمكافئ ثيفينن.

\[\frac{V_A-10}{4}+0.2V_A+\frac{V_A}{5}=0\]
\[V_A=\frac{50}{13}\,\mathrm V,\qquad I_L=\frac{V_A}{5}=\boxed{\frac{10}{13}\,\mathrm A}\]

Conclusion: Dependent sources remain active when determining \(R_{\mathrm{Th}}\); only independent sources are deactivated. The test-source method gives the correct terminal resistance. A dependent source must never be removed merely because the independent sources were zeroed.

الاستنتاج: تبقى المنابع التابعة فعالة عند حساب \(R_{\mathrm{Th}}\)، بينما تصفر المنابع المستقلة فقط. وتتيح طريقة منبع الاختبار حساب المقاومة المكافئة الصحيحة من الطرفين. ولا يجوز حذف المنبع التابع لمجرد تصفير المنابع المستقلة.

Try it yourself — dependent voltage source (advanced)

مسألة للمحاولة — منبع جهد تابع (مستوى متقدم)

Problem: Determine the Thévenin equivalent seen from terminals a–b. The circuit contains \(5\,\Omega\), \(10\,\Omega\) and \(15\,\Omega\) resistors and a voltage-controlled dependent voltage source \(4v_x\) (positive terminal on the left). The controlling voltage \(v_x\) is across the \(5\,\Omega\) resistor, positive at its upper terminal. There are no independent sources. Try finding \(V_{\mathrm{Th}}\) and \(R_{\mathrm{Th}}\) before reading the solution.

المطلوب: أوجد مكافئ ثيفينن كما يُرى من الطرفين a وb. تحتوي الدارة على مقاومات \(5\,\Omega\) و\(10\,\Omega\) و\(15\,\Omega\)، ومنبع جهد تابع للجهد مقداره \(4v_x\) (قطبه الموجب إلى اليسار). الجهد المتحكم \(v_x\) هو الجهد على مقاومة \(5\,\Omega\)، وقطبه الموجب في الأعلى. لا توجد منابع مستقلة. حاول إيجاد \(V_{\mathrm{Th}}\) و\(R_{\mathrm{Th}}\) قبل قراءة الحل.

5 Ω10 Ω+−4vx15 Ω+−vxabxyOpen terminals / طرفان مفتوحان
Original circuit and defined voltage polarity / الدارة الأصلية مع قطبية الجهد المحددة

Step 1 — Choose the reference and write the controlling relation

Take b as ground. Denote the top of \(5\,\Omega\) by \(V_x=v_x\), the node left of the dependent voltage source by \(V_y\), and the output terminal by \(V_a\). KCL at x and the source voltage constraint give:

الخطوة 1 — تحديد المرجع وكتابة علاقة التحكم

نختار b مرجعاً للجهد. نرمز إلى جهد العقدة أعلى مقاومة \(5\,\Omega\) بالرمز \(V_x=v_x\)، وإلى العقدة يسار المنبع التابع بالرمز \(V_y\)، وإلى طرف الخرج بالرمز \(V_a\). بتطبيق قانون كيرشوف للتيارات عند x وكتابة علاقة جهد المنبع نحصل على:

\[\frac{V_x}{5}+\frac{V_x-V_y}{10}=0\quad\Longrightarrow\quad V_y=3V_x\]
\[V_y-V_a=4v_x=4V_x\quad\Longrightarrow\quad V_a=-V_x\]

Step 2 — Find the open-circuit voltage

With a–b open and no independent source present, apply KCL to the supernode containing y and a. The \(15\,\Omega\) branch remains connected inside the network.

الخطوة 2 — حساب جهد الدارة المفتوحة

مع بقاء الطرفين a وb مفتوحين وعدم وجود منابع مستقلة، نطبق قانون كيرشوف للتيارات على العقدة الفائقة التي تضم y وa. تبقى مقاومة \(15\,\Omega\) موصولة داخل الشبكة.

\[\frac{V_y-V_x}{10}+\frac{V_a}{15}=0\]
\[\frac{3V_x-V_x}{10}-\frac{V_x}{15}=0\quad\Longrightarrow\quad\frac{2V_x}{15}=0\]
\[\boxed{V_x=0,\qquad V_{\mathrm{Th}}=V_a-V_b=0\,\mathrm V}\]

Step 3 — Apply a test source to calculate the equivalent resistance

Do not deactivate the dependent voltage source. Connect an ideal \(1\,\mathrm V\) test source with its positive terminal at a. Define \(I_{\mathrm{test}}\) positive entering the network from a. Thus \(V_a=1\,\mathrm V\).

الخطوة 3 — وصل منبع اختبار لحساب المقاومة المكافئة

لا نصفر منبع الجهد التابع. نصل منبع جهد اختبار مثالي \(1\,\mathrm V\) بقطبه الموجب عند a، ونفترض \(I_{\mathrm{test}}\) موجباً عندما يدخل الشبكة من الطرف a. بالتالي \(V_a=1\,\mathrm V\).

5 Ω10 Ω+−4vx15 Ω+−vxabxy+−Vtest = 1 VItest ←
Test voltage source across a–b / منبع الاختبار بين a وb
\[V_a=-V_x=1\,\mathrm V\quad\Longrightarrow\quad V_x=-1\,\mathrm V,\quad V_y=-3\,\mathrm V\]

Step 4 — Calculate test current using the supernode

The test current entering the network equals the sum of currents leaving the supernode through the \(10\,\Omega\) and \(15\,\Omega\) resistors. A negative result means the actual current flows from the network into the test source.

الخطوة 4 — حساب تيار الاختبار باستخدام العقدة الفائقة

تيار الاختبار الداخل إلى الشبكة يساوي مجموع التيارين الخارجين من العقدة الفائقة عبر مقاومتي \(10\,\Omega\) و\(15\,\Omega\). تعني النتيجة السالبة أن اتجاه التيار الفعلي من الشبكة نحو منبع الاختبار.

\[I_{\mathrm{test}}=\frac{V_y-V_x}{10}+\frac{V_a}{15}\]
\[I_{\mathrm{test}}=\frac{-3-(-1)}{10}+\frac{1}{15}=-\frac{2}{15}\,\mathrm A\]
\[\boxed{R_{\mathrm{Th}}=\frac{V_{\mathrm{test}}}{I_{\mathrm{test}}}=\frac{1}{-2/15}=-7.5\,\Omega}\]

Step 5 — Interpret and verify the result

The equivalent is a zero-voltage Thévenin source in series with \(-7.5\,\Omega\). The negative resistance represents active terminal behaviour made possible by the dependent source; it is not an ordinary passive resistor. As a check, a \(1\,\mathrm A\) test current entering the network would produce \(V_a=-7.5\,\mathrm V\). Never remove the dependent source while finding the resistance.

الخطوة 5 — تفسير النتيجة والتحقق منها

المكافئ هو منبع ثيفينن جهده صفر على التسلسل مع مقاومة مكافئة \(-7.5\,\Omega\). تدل المقاومة السالبة على سلوك فعال عند طرفي الشبكة يمكن أن يسببه المنبع التابع، ولا تمثل مقاومة سلبية عادية. وللتحقق، فإن حقن تيار اختبار \(1\,\mathrm A\) داخل الشبكة يعطي \(V_a=-7.5\,\mathrm V\). لا يجوز حذف المنبع التابع عند حساب المقاومة.

\[\boxed{V_{\mathrm{Th}}=0\,\mathrm V,\qquad R_{\mathrm{Th}}=-7.5\,\Omega}\]

Final Thévenin equivalent — complete and simplified diagrams

The zero-volt ideal voltage source is equivalent to a short circuit. Both diagrams below represent the same two-terminal active network.

دارة ثيفينن المكافئة النهائية — الشكل الكامل والمبسط

يعادل منبع الجهد المثالي الصفري قصرا كهربائيا، ولذلك يمثل الشكلان التاليان الشبكة الفعالة نفسها كما ترى من الطرفين.

+− 0 V RTh = −7.5 Ω ab Complete Thévenin equivalent
Complete circuit / مكافئ ثيفينن الكامل
Req = −7.5 Ω ab Simplified equivalent
Simplified circuit / الدارة المكافئة المبسطة

Important: The negative value is the input resistance of an active network containing a dependent source. It is not a conventional passive resistor; the drawn resistor symbol represents its two-terminal equivalent behavior.

تنبيه: القيمة السالبة تمثل مقاومة الدخل المكافئة لشبكة فعالة تحتوي على منبع تابع، وليست مقاومة سلبية تقليدية. يعبّر رمز المقاومة المرسوم عن سلوك الشبكة المكافئ بين طرفيها.

Physical meaning of a negative resistance

A normal positive resistor absorbs electrical power, usually as heat. A negative equivalent resistance describes an active network that can deliver power through its terminals. It is not an ordinary resistor with a negative material resistance.

ما المعنى الفيزيائي للمقاومة السالبة؟

تمتص المقاومة الموجبة العادية الاستطاعة الكهربائية وتحولها غالبا إلى حرارة. أما المقاومة المكافئة السالبة فتعبر عن شبكة فعالة يمكنها تقديم استطاعة إلى الدارة الخارجية، وليست مقاومة عادية مصنوعة من مادة ذات مقاومة سالبة.

In this example: If a test current of \(1\,\mathrm A\) enters the network at terminal a, the terminal voltage is \(-7.5\,\mathrm V\). The absorbed terminal power is negative; therefore the network delivers \(7.5\,\mathrm W\) to the test source under this test condition.

في مثالنا: إذا دخل تيار اختبار مقداره \(1\,\mathrm A\) من الطرف a، يصبح الجهد بين الطرفين \(-7.5\,\mathrm V\). تكون الاستطاعة الممتصة سالبة، أي أن الشبكة تقدم \(7.5\,\mathrm W\) إلى منبع الاختبار في حالة القياس هذه.

\[P_{\mathrm{absorbed}}=V_{ab}I_{\mathrm{test}}=(-7.5)(1)=\boxed{-7.5\,\mathrm W}\]

Where does the energy come from? In a real electronic circuit, an active device needs an external power supply. The ideal dependent source models its behaviour without showing that supply. Thus negative resistance does not violate conservation of energy. Actual circuits also have operating limits and may become unstable with some loads.

من أين تأتي الطاقة؟ تحتاج العناصر الفعالة في الدارات الحقيقية إلى مصدر تغذية خارجي. يمثل المنبع التابع المثالي سلوك هذه العناصر دون إظهار مصدر تغذيتها. لذلك لا تخالف المقاومة السالبة مبدأ انحفاظ الطاقة. كما أن للدارات الحقيقية حدود تشغيل، وقد تصبح غير مستقرة عند توصيل أحمال معينة.

1899

Star–delta transformation

تحويل النجمة والمثلث

Kennelly published triangle/star equivalence in conducting networks in 1899. This transforms three-terminal resistor groups that block direct series/parallel reduction.
نشر كينيلي تكافؤ المثلث والنجمة في الشبكات الناقلة عام 1899. يسمح التحويل بتبديل مجموعة مقاومات ثلاثية الأطراف تعيق الاختزال المباشر.
Why use it / advantage: Handles many bridge networks while preserving terminal behavior.
الفائدة / الميزة: يعالج كثيرًا من الشبكات الجسرية مع حفظ سلوك الأطراف.
Limitation: Repeated conversions can be lengthy; internal currents of the replaced group must be recovered separately.
القيد / العيب: قد تطول التحويلات المتكررة؛ تُستعاد تيارات المجموعة الداخلية المحذوفة بحساب مستقل.

Derivation and engineering interpretation

اشتقاق العلاقات والتفسير الهندسي

A delta (Δ) and a star (Y, or its equivalent T layout) are interchangeable three-terminal networks when their resistances measured between every pair of terminals are equal, with the third terminal open. This is a terminal equivalence, not equality of currents in individual internal branches.
تكون شبكتا المثلث Δ والنجمة Y (أو رسمها المكافئ T) متكافئتين إذا تساوت المقاومة المقاسة بين كل زوج من الأطراف الثلاثة مع ترك الطرف الثالث مفتوحا. التكافؤ عند الأطراف الخارجية ولا يعني تساوي تيارات الفروع الداخلية.

Visual derivation: equivalent resistance between A and B

Leave terminal C externally open. In the delta (Δ), the direct branch \(R_{AB}\) is in parallel with the series path \(R_{CA}+R_{BC}\). In the star (Y), no current flows through \(\(R_C\)\), so only \(\(R_A\)+\(R_B\)\) remains between A and B.

الاشتقاق بالرسم: المقاومة المكافئة بين A وB

نترك الطرف C مفتوحا خارجيا. في المثلث Δ يوجد مساران متوازيان بين A وB: المقاومة المباشرة \(R_{AB}\)، والمسار المتسلسل \(R_{CA}+R_{BC}\). أما في النجمة Y فلا يمر تيار في \(\(R_C\)\)، فتكون المقاومة بين A وB هي \(\(R_A\)+\(R_B\)\).

Δ — Delta Y — Star C open C open ABC ABCO RCA RBC RAB RC RA RB RAB ∥ (RCA + RBC) RA + RB ⇔
Same equivalent resistance between A and B, with terminal C open.المقاومة المكافئة نفسها بين الطرفين A وB، مع ترك الطرف C مفتوحا.

Consequently, the two arrangements must satisfy the following equality. For the remaining pairs, rotate the terminal labels: B–C with A open, and C–A with B open.

وبالتالي، يجب أن تحقق الشبكتان علاقة التكافؤ الآتية. ولاشتقاق العلاقتين الأخريين نبدل الأطراف دوريا: B وC مع فتح A، ثم C وA مع فتح B.

\[R_{AB}^{(Y)}=R_A+R_B=R_{AB}\parallel(R_{CA}+R_{BC})\]
\[R_{BC}^{(Y)}=R_B+R_C=R_{BC}\parallel(R_{AB}+R_{CA})\]
\[R_{CA}^{(Y)}=R_C+R_A=R_{CA}\parallel(R_{AB}+R_{BC})\]

Step-by-step derivation: Δ → Y

Start with the three terminal-equivalence equations above. Define the sum of delta resistances:

الاشتقاق خطوة بخطوة: من المثلث إلى النجمة

ننطلق من معادلات التكافؤ الثلاث بين الأطراف، ونعرف مجموع مقاومات المثلث:

\[S=R_{AB}+R_{BC}+R_{CA}\]

Step 1 — Expand each parallel combination

Use the parallel formula. Each denominator becomes \(S\).

الخطوة 1 — فك كل علاقة تواز

نستخدم قانون المقاومتين على التوازي. نلاحظ أن مقام كل كسر يساوي \(S\).

\[R_A+R_B=\frac{R_{AB}(R_{CA}+R_{BC})}{S}\]
\[R_B+R_C=\frac{R_{BC}(R_{AB}+R_{CA})}{S}\]
\[R_C+R_A=\frac{R_{CA}(R_{AB}+R_{BC})}{S}\]

Step 2 — Isolate \(R_A\)

Add the first and third equations, then subtract the second. The \(R_B\) and \(R_C\) terms cancel.

الخطوة 2 — عزل مقاومة \(R_A\)

نجمع المعادلتين الأولى والثالثة، ثم نطرح الثانية. تختفي حدود \(R_B\) و\(R_C\)، ويبقى ضعف \(R_A\).

\[2R_A=(R_A+R_B)+(R_C+R_A)-(R_B+R_C)\]

Substitute the corresponding fractions, using the common denominator \(S\):

نعوض الكسور المقابلة مع توحيد المقام \(S\):

\[\begin{aligned}2R_A={}&\frac{R_{AB}(R_{CA}+R_{BC})}{S}\\[5pt]&+\frac{R_{CA}(R_{AB}+R_{BC})}{S}\\[5pt]&-\frac{R_{BC}(R_{AB}+R_{CA})}{S}\end{aligned}\]

Expand the products. Equal positive and negative cross-products cancel, leaving two copies of \(R_{AB}\) \(R_{CA}\).

نوزع الجداءات في البسط، ونختزل الحدود المتساوية ذات الإشارات المتعاكسة، فيبقى ضعف الجداء بين \(R_{AB}\) و\(R_{CA}\).

\[2R_A=\frac{2R_{AB}R_{CA}}{S}\]
\[\boxed{R_A=\frac{R_{AB}R_{CA}}{S}}\]

Step 3 — Find \(R_B\) and \(R_C\)

Use the same add–subtract operation, changing which equation is subtracted:

الخطوة 3 — حساب \(R_B\) و\(R_C\)

نكرر عملية الجمع والطرح، لكن نغير المعادلة التي نطرحها في كل مرة:

\[2R_B=(R_A+R_B)+(R_B+R_C)-(R_C+R_A)\]
\[\boxed{R_B=\frac{R_{AB}R_{BC}}{S}}\]
\[2R_C=(R_B+R_C)+(R_C+R_A)-(R_A+R_B)\]
\[\boxed{R_C=\frac{R_{BC}R_{CA}}{S}}\]

Rule: A star arm is the product of the two delta sides meeting at its terminal, divided by the sum of all three delta sides.

القاعدة: مقاومة كل ذراع في النجمة تساوي جداء مقاومتي المثلث المتصلتين بالطرف نفسه، مقسوما على مجموع مقاومات المثلث الثلاث.

Step-by-step reverse derivation: Y → Δ

To derive the reverse conversion, begin with the already established delta-to-star expressions.

الاشتقاق العكسي خطوة بخطوة: من النجمة إلى المثلث

لاشتقاق التحويل العكسي، ننطلق من علاقات التحويل السابقة من المثلث إلى النجمة.

Step 4 — Why do we combine these expressions to find \(R_{AB}\)?

Goal: Express the unknown delta side \(R_{AB}\) using only the three known star arms \(R_A\), \(R_B\), and \(R_C\). We begin with the already-derived formulas, rather than choosing multiplication arbitrarily.

الخطوة 4 — لماذا نجمع هذه العلاقات لإيجاد \(R_{AB}\)؟

الهدف: كتابة مقاومة ضلع المثلث المجهولة \(R_{AB}\) باستخدام مقاومات النجمة المعلومة فقط، وهي \(R_A\) و\(R_B\) و\(R_C\). ننطلق من العلاقات التي سبق اشتقاقها، وليس من عملية ضرب عشوائية.

First: Add \(R_A\) and \(R_B\). Notice that \(R_{AB}\) appears as a common factor, but another unknown factor remains in parentheses.

أولا: نجمع \(R_A\) و\(R_B\). نلاحظ ظهور \(R_{AB}\) عاملا مشتركا، لكن يبقى داخل القوس حد آخر مجهول.

\[R_A+R_B=\frac{R_{AB}(R_{CA}+R_{BC})}{S}\]

Since \(S=R_{AB}+R_{BC}+R_{CA}\), the parenthesized sum equals \(S-R_{AB}\). Therefore:

بما أن \(S=R_{AB}+R_{BC}+R_{CA}\)، فإن مجموع الحدين داخل القوس يساوي \(S-R_{AB}\). لذلك:

\[R_A+R_B=\frac{R_{AB}(S-R_{AB})}{S}\]
\[R_A+R_B=R_{AB}-\frac{R_{AB}^{2}}{S}\]

Now we can see the reason: To isolate \(R_{AB}\), we need an expression involving only known star resistances that equals the unwanted term \(R_{AB}^{2}/S\). The product \(R_AR_B/R_C\) provides exactly that expression.

وهنا يتضح السبب: لعزل \(R_{AB}\)، نحتاج إلى علاقة تحتوي على مقاومات النجمة المعلومة فقط وتساوي الحد الذي نريد التخلص منه، وهو \(R_{AB}^{2}/S\). وتحقق الكمية \(R_AR_B/R_C\) ذلك تماما.

Substitute the three delta-to-star relations into this ratio and cancel the common factors:

نعوض علاقات التحويل الثلاث في هذه النسبة، ثم نختزل العوامل المشتركة:

\[\frac{R_AR_B}{R_C}=\frac{\left(\frac{R_{AB}R_{CA}}{S}\right)\left(\frac{R_{AB}R_{BC}}{S}\right)}{\frac{R_{BC}R_{CA}}{S}}\]
\[\boxed{\frac{R_AR_B}{R_C}=\frac{R_{AB}^{2}}{S}}\]

Finally: Add this ratio to \(R_A+R_B\). The negative and positive square terms cancel, leaving the desired \(R_{AB}\).

أخيرا: نضيف هذه النسبة إلى مجموع \(R_A+R_B\). يختفي الحد التربيعي الموجب مع نظيره السالب، وتبقى المقاومة المطلوبة \(R_{AB}\).

\[\begin{aligned}R_A+R_B+\frac{R_AR_B}{R_C}&=R_{AB}-\frac{R_{AB}^{2}}{S}+\frac{R_{AB}^{2}}{S}\\[5pt]&=R_{AB}\end{aligned}\]
\[\boxed{R_{AB}=R_A+R_B+\frac{R_AR_B}{R_C}}\]

Step 5 — Derive the other two delta sides

Repeat the same reasoning for the other two terminal pairs.

الخطوة 5 — اشتقاق الضلعين الآخرين

نكرر العملية نفسها لزوجي الأطراف الآخرين.

\[\boxed{R_{BC}=R_B+R_C+\frac{R_BR_C}{R_A}}\]
\[\boxed{R_{CA}=R_C+R_A+\frac{R_CR_A}{R_B}}\]

Step 6 — Express the result compactly

Define \(Q\) as the sum of all pairwise products of star arms. Each delta side equals \(Q\) divided by the opposite star arm.

الخطوة 6 — الصيغة النهائية المختصرة

نعرف \(Q\) بأنه مجموع جداءات أزواج مقاومات النجمة. يساوي كل ضلع من المثلث \(Q\) مقسوما على ذراع النجمة المقابل له.

\[Q=R_AR_B+R_BR_C+R_CR_A\]
\[R_{AB}=\frac{Q}{R_C}\]
\[R_{BC}=\frac{Q}{R_A}\]
\[R_{CA}=\frac{Q}{R_B}\]

Note: The reverse formulas assume nonzero star-arm resistances. A zero arm requires considering the limiting case.

ملاحظة: تفترض علاقات التحويل العكسي أن مقاومات أذرع النجمة غير صفرية. إذا كان أحد الأذرع صفريا فتدرس الحالة الحدية بصورة منفصلة.

Worked example

مثال محلول بالتفصيل

Δ — DeltaY — Star CABCABO RCA = 3 ΩRBC = 9 ΩRAB = 6 Ω RC = 1.5 ΩRA = 1 ΩRB = 3 Ω ⇔
Three common terminals A, B, C; star center O / ثلاثة أطراف مشتركة A وB وC ومركز النجمة O
Delta: \(R_{AB}\) = \(6\,\Omega\), \(R_{BC}\) = \(9\,\Omega\), \(R_{CA}\) = \(3\,\Omega\). Convert to a star and check resistance seen between A and B with C externally open.
مثلث مقاومات \(R_{AB}\) = \(6\,\Omega\) و\(R_{BC}\) = \(9\,\Omega\) و\(R_{CA}\) = \(3\,\Omega\). حوّله إلى نجمة وتحقق من المقاومة بين A وB مع ترك C مفتوحًا خارجيًا.
  1. Add all delta resistances.
    اجمع مقاومات المثلث.
    \[S=6+9+3=18\,\Omega\]
  2. Each star arm uses the two delta sides touching its terminal.
    كل ذراع نجمة يساوي حاصل ضرب ضلعي المثلث المتصلين بطرفه مقسومًا على المجموع.
    \[\begin{aligned}R_A&=\frac{6(3)}{18}=1\,\Omega\\[8pt]R_B&=\frac{6(9)}{18}=3\,\Omega\\[8pt]R_C&=\frac{9(3)}{18}=1.5\,\Omega\end{aligned}\]
  3. Verify the two-terminal resistance; the third arm carries no external current.
    تحقق من المقاومة بين الطرفين؛ لا يمر تيار خارجي في الذراع الثالث.
    \[\begin{aligned}R_{\Delta}&=6\parallel(3+9)=4\,\Omega\\[8pt]R_Y&=R_A+R_B=1+3=4\,\Omega\end{aligned}\]
  4. Reverse the conversion: the delta side is the sum of pair products divided by the opposite star arm.
    اعكس التحويل؛ ضلع المثلث يساوي مجموع جداءات أذرع النجمة الثنائية مقسومًا على الذراع المقابل.
    \[\begin{aligned}Q&=R_AR_B+R_BR_C+R_CR_A=9\,\Omega^2\\[8pt]R_{AB}&=\frac{Q}{R_C}=6\,\Omega\\[8pt]R_{BC}&=\frac{Q}{R_A}=9\,\Omega\\[8pt]R_{CA}&=\frac{Q}{R_B}=3\,\Omega\end{aligned}\]

Balanced network and practical use

الشبكة المتوازنة والاستخدام العملي

If all three delta resistances are equal and all three star arms are equal, each delta resistance is three times a star arm. The conversion helps simplify bridge networks that cannot be reduced by ordinary series/parallel combinations, as well as resistive three-phase and filter networks.
عندما تتساوى مقاومات المثلث الثلاث وتتساوى أذرع النجمة الثلاث، تكون مقاومة كل ضلع في المثلث ثلاثة أضعاف مقاومة ذراع النجمة. يفيد التحويل في تبسيط الشبكات الجسرية التي لا تختزل مباشرة بالتوالي والتوازي، وكذلك في شبكات الأطوار الثلاثة والمرشحات المقاومة.
\[R_{AB}=R_{BC}=R_{CA}=R_{\Delta}\quad\Longrightarrow\quad R_A=R_B=R_C=R_Y=\frac{R_{\Delta}}{3}\]

Second numerical check

تحقق عددي ثان

Delta (Δ) Star (Y) C open C open ABC ABCO RCA = 10 Ω RBC = 15 Ω RAB = 25 Ω RC = 3 Ω RA = 5 Ω RB = 7.5 Ω ⇔
Delta and star networks with the same terminals A, B and C. شبكتا المثلث والنجمة المتكافئتان عند الأطراف A وB وC.
\[R_{AB}^{(\Delta)}=25\parallel(10+15)=12.5\,\Omega\]
\[R_{AB}^{(Y)}=R_A+R_B=5+7.5=12.5\,\Omega\]
For delta values \(R_{AB}\) = \(25\,\Omega\), \(R_{CA}\) = \(10\,\Omega\) and \(R_{BC}\) = \(15\,\Omega\), the sum is \(50\,\Omega\). The star equivalents are \(R_A\) = \(5\,\Omega\), \(R_B\) = \(7.5\,\Omega\) and \(R_C\) = \(3\,\Omega\). Checking A–B with C open gives 25 ∥ (10 + 15) = \(12.5\,\Omega\) = 5 + \(7.5\,\Omega\).
إذا كانت مقاومات المثلث \(R_{AB}\) = \(25\,\Omega\) و\(R_{CA}\) = \(10\,\Omega\) و\(R_{BC}\) = \(15\,\Omega\)، فمجموعها \(50\,\Omega\). تصبح أذرع النجمة \(R_A\) = \(5\,\Omega\) و\(R_B\) = \(7.5\,\Omega\) و\(R_C\) = \(3\,\Omega\). للتحقق بين A وB مع فتح C نجد 25 ∥ (10 + 15) = \(12.5\,\Omega\) وهي تساوي 5 + \(7.5\,\Omega\).
\[R_A=\frac{25\cdot10}{50}=5\,\Omega,\quad R_B=\frac{25\cdot15}{50}=7.5\,\Omega,\quad R_C=\frac{15\cdot10}{50}=3\,\Omega\]
For an open third terminal, its external current is zero, but the corresponding delta network may still carry current through its two-series-resistor path. The conversion preserves terminal behavior, not individual branch currents.
عند فتح الطرف الثالث يكون تياره الخارجي صفرا، لكن قد يمر تيار في مسار المقاومتين المتصلتين على التوالي داخل المثلث. يحافظ التحويل على السلوك الخارجي ولا يحافظ بالضرورة على تيارات كل فرع داخلي.
1926

Mayer–Norton equivalent

مكافئ ماير–نورتن

Hans Ferdinand Mayer published a current-source equivalent in November 1926; Edward Lawry Norton described it independently in an internal Bell Laboratories memorandum that year.
نشر هانس فرديناند ماير المكافئ التياري في نوفمبر 1926؛ ووصفه إدوارد لوري نورتن مستقلًا في مذكرة داخلية لمختبرات بِل في العام نفسه.
Why use it / advantage: Convenient current-source model for parallel loads.
الفائدة / الميزة: تمثيل تياري ملائم للأحمال المتوازية.
Limitation: An ideal short-circuit current is a mathematical model and should not be measured by indiscriminately shorting a real power source.
القيد / العيب: تيار القصر المثالي نموذج حسابي؛ لا يُقاس بقصر مصدر قدرة حقيقي بصورة عشوائية.

Steps of Norton's method

For a linear two-terminal network, the Norton equivalent consists of an ideal current source \(I_{\mathrm N}\) in parallel with a resistance \(R_{\mathrm N}\). Follow the steps below before solving the example.

خطوات تطبيق طريقة نورتن

نستبدل الشبكة الخطية ذات الطرفين بمنبع تيار مثالي \(I_{\mathrm N}\) على التوازي مع مقاومة \(R_{\mathrm N}\). نتبع الخطوات الآتية قبل حل المثال.

  1. Identify the load terminals: Mark terminals A and B, then disconnect the load \(R_L\) without changing the internal network.
    تحديد طرفي الحمل: نحدد الطرفين A وB، ثم نفصل الحمل \(R_L\) مع إبقاء الشبكة الداخلية دون تغيير.
  2. Determine the short-circuit current: Connect A directly to B in the circuit model and calculate the current through this ideal short, with a clearly defined direction. This is the Norton current.
    حساب تيار القصر: نصل A مع B بقصر مثالي في النموذج الحسابي، ونحسب التيار المار في القصر بعد تحديد اتجاهه. وهو تيار نورتن.
    \[I_{\mathrm N}=I_{\mathrm{SC}}\]
  3. Find the Norton resistance: Keep the load disconnected. Zero independent ideal voltage sources by shorting them and independent ideal current sources by opening them, then calculate the resistance seen from A–B. Leave dependent sources active; use a test source if needed.
    حساب مقاومة نورتن: مع فصل الحمل، نصفر منابع الجهد المثالية المستقلة بقصرها، ومنابع التيار المثالية المستقلة بفتحها، ثم نحسب المقاومة كما ترى من A وB. تبقى المنابع التابعة فعالة ويستخدم منبع اختبار عند الحاجة.
    \[R_{\mathrm N}=R_{\mathrm{Th}}\]
  4. Draw the Norton equivalent: Connect \(I_{\mathrm N}\) in parallel with \(R_{\mathrm N}\), then reconnect \(R_L\) across the same two terminals.
    رسم مكافئ نورتن: نوصل \(I_{\mathrm N}\) على التوازي مع \(R_{\mathrm N}\)، ثم نعيد توصيل \(R_L\) على الطرفين نفسيهما.
  5. Calculate and verify: For resistive loads, use the current-divider rule to find the load current and Ohm's law for its voltage. Verify that the corresponding Thévenin voltage is \(I_{\mathrm N}R_{\mathrm N}\).
    الحساب والتحقق: للأحمال المقاومة نستخدم قانون تقسيم التيار لإيجاد تيار الحمل، ثم قانون أوم لحساب جهده. ونتحقق من أن جهد ثيفينن المكافئ يساوي \(I_{\mathrm N}R_{\mathrm N}\).
    \[I_L=I_{\mathrm N}\frac{R_{\mathrm N}}{R_{\mathrm N}+R_L}\]
    \[V_L=I_LR_L,\qquad V_{\mathrm{Th}}=I_{\mathrm N}R_{\mathrm N}\]

Safety note: Short-circuiting is a mathematical analysis step, not an instruction to short an energized real power source.

تنبيه للسلامة: القصر هنا إجراء حسابي لتحليل الدارة، وليس توجيها لقصر منبع قدرة حقيقي أثناء التشغيل.

Worked example

مثال محلول بالتفصيل

+− 12 V4 Ω 6 Ω3 Ω RL AB
Original network with the load connected.الدارة الأصلية مع توصيل مقاومة الحمل.
Use the \(12\,\mathrm{V}\), \(4\,\Omega\), \(6\,\Omega\) network from the 1883 card. Find its current-source equivalent.
استخدم شبكة \(12\,\mathrm{V}\) و\(4\,\Omega\) و\(6\,\Omega\) من بطاقة 1883. احسب مكافئها التياري.
  1. Short A–B mathematically. The \(6\,\Omega\) resistor has zero voltage, so all source current through \(4\,\Omega\) goes into the short.
    اقصر A وB حسابيًا. يصبح جهد مقاومة \(6\,\Omega\) صفرًا، ويتجه تيار مقاومة \(4\,\Omega\) إلى القصر.
    \[I_N=I_{\mathrm{sc}}=\frac{12}{4}=3\,\mathrm A\]
  2. Deactivate the independent source and find resistance seen at the terminals.
    عطل المصدر المستقل واحسب المقاومة من الطرفين.
    \[R_N=4\parallel6=2.4\,\Omega\]
  3. The equivalent source injects current from B toward A; load current flows A to B. Apply current division.
    مصدر المكافئ يحقن التيار من B نحو A؛ تيار الحمل من A إلى B. طبّق تقسيم التيار.
    \[\begin{aligned}R_L&=3\,\Omega\\[8pt]I_L&=\frac{I_NR_N}{R_N+R_L}=\frac{3(2.4)}{5.4}=\frac43\,\mathrm A\end{aligned}\]
  4. Check agreement with the voltage-source equivalent.
    تحقق من الاتفاق مع المكافئ الجهدي.
    \[\begin{aligned}I_NR_N&=3(2.4)=7.2\,\mathrm V=V_{\mathrm{Th}}\\[8pt]R_N&=R_{\mathrm{Th}}\end{aligned}\]

Final Norton equivalent circuit

The Norton current source \(I_{\mathrm N}=3\,\mathrm A\) feeds the parallel Norton resistance \(R_{\mathrm N}=2.4\,\Omega\) and load \(R_L=3\,\Omega\). The source current is directed from B to A, and the load current from A to B.

دارة نورتن المكافئة النهائية

يغذي منبع تيار نورتن \(I_{\mathrm N}=3\,\mathrm A\) المقاومة المكافئة \(R_{\mathrm N}=2.4\,\Omega\) والحمل \(R_L=3\,\Omega\) على التوازي. يتجه تيار المنبع من B إلى A، وتيار الحمل من A إلى B.

IN = 3 A RN 2.4 Ω RL 3 Ω IL A B Norton current source and two parallel resistances
Norton equivalent with the load connected.مكافئ نورتن مع إعادة توصيل الحمل.
\[I_L=I_{\mathrm N}\frac{R_{\mathrm N}}{R_{\mathrm N}+R_L}=3\frac{2.4}{2.4+3}=\frac43\,\mathrm A\]
\[V_{AB}=I_LR_L=\frac43\cdot3=4\,\mathrm V\]
After 1926 · equivalent-source formulation

Source transformation

تحويل المصادر

Presented here after both equivalent-source forms, as their algebraic relationship; no separate discovery year is asserted. Earlier work may contain equivalent transformations.
يُعرض هنا بعد تأسيس شكلي المكافئ، بوصفه العلاقة الجبرية بينهما؛ لا تُدّعى سنة اكتشاف مستقلة. قد تتضمن الأعمال الأقدم تحويلات مكافئة.
Why use it / advantage: Can simplify a network before solving equations.
الفائدة / الميزة: قد يبسط الشبكة قبل كتابة المعادلات.
Limitation: Only preserves behavior at the chosen terminals; the resistor must have the required series/parallel topology. A bare ideal source is not generally convertible with a finite resistance.
القيد / العيب: يحفظ سلوك الطرفين المختارين فقط؛ يجب تحقق توالي المقاومة أو توازيها الصحيح. لا يُحوّل مصدر مثالي منفرد عمومًا بمقاومة محدودة.

Steps of source transformation

A practical voltage source modeled as an ideal voltage source \(V_s\) in series with \(R_s\) has an equivalent ideal current-source model \(I_s\) in parallel with the same resistance. Both models must have identical current–voltage behavior at their external terminals.

خطوات تطبيق طريقة تحويل المصادر

يمكن استبدال منبع جهد مثالي \(V_s\) مع مقاومة متسلسلة \(R_s\) بمنبع تيار مثالي مكافئ \(I_s\) مع المقاومة نفسها على التوازي. ويجب أن يحافظ الشكلان على علاقة الجهد والتيار عند طرفي الخرج.

  1. Identify the source and its resistance: Confirm that the voltage source and resistance form a series two-terminal source network, or that the current source and resistance form a parallel two-terminal source network. Identify output polarity A (+) and B (−).
    تحديد المنبع ومقاومته: نتحقق من أن منبع الجهد ومقاومته يشكلان شبكة منبع متسلسلة ذات طرفين، أو أن منبع التيار ومقاومته على التوازي. ونحدد قطبية الخرج A (+) وB (−).
  2. Convert voltage source to current source: Divide the source voltage by its series resistance. Move the unchanged resistance to the parallel branch.
    التحويل من منبع جهد إلى منبع تيار: نقسم جهد المنبع على مقاومته المتسلسلة، ثم نمثل المقاومة نفسها على التوازي مع منبع التيار.
    \[I_s=\frac{V_s}{R_s},\qquad R_{\parallel}=R_s\]
  3. Set the current direction: Direct the current-source arrow toward the terminal corresponding to the positive pole of the original voltage source. This preserves the open-circuit voltage polarity.
    تحديد اتجاه التيار: نوجه سهم منبع التيار نحو الطرف الموافق للقطب الموجب لمنبع الجهد الأصلي، حتى نحافظ على قطبية جهد الدارة المفتوحة.
    \[V_{\mathrm{OC}}=I_sR_s=V_s\]
  4. Reconnect the original load: Connect the same load across A–B. In the current-source model, use current division to find the resistive load current.
    إعادة توصيل الحمل الأصلي: نوصل الحمل نفسه بين A وB. وفي نموذج منبع التيار نستخدم قانون تقسيم التيار لحساب تيار الحمل المقاومي.
    \[I_L=I_s\frac{R_s}{R_s+R_L}\]
  5. Check the conversion and reverse direction: Verify that the original voltage-source circuit produces the same load current and voltage. Conversely, convert a parallel current source into a series voltage source using \(V_s=I_sR_s\).
    التحقق والتحويل العكسي: نتأكد من أن الدارة الجهدية الأصلية تعطي تيار الحمل وجهده نفسيهما. وفي التحويل العكسي نستبدل منبع التيار المتوازي بمنبع جهد متسلسل وفق \(V_s=I_sR_s\).
    \[I_L=\frac{V_s}{R_s+R_L},\qquad V_s=I_sR_s\]

Important: This conversion is a terminal equivalence, not a replacement for arbitrary series or parallel source connections. Do not treat the load resistance as the internal source resistance.

تنبيه: يحافظ التحويل على سلوك الطرفين الخارجيين، ولا يصح تطبيقه على أي توصيل عشوائي للمنابع والمقاومات. كما يجب عدم الخلط بين مقاومة المنبع ومقاومة الحمل.

Worked example

مثال محلول بالتفصيل

Voltage-source formCurrent-source form +− 10 V 5 ΩRL5 Ω 2 A Rs5 Ω RL5 Ω IL AB AB ⇔ Series source resistanceParallel source resistance
Two equivalent source networks with the same 5 Ω load.شبكتا منبعين متكافئتين مع حمل واحد مقاومته \(5\,\Omega\).
A \(10\,\mathrm{V}\) source in series with \(5\,\Omega\) feeds a \(5\,\Omega\) load. Convert it to the current-source form.
مصدر \(10\,\mathrm{V}\) على التوالي مع \(5\,\Omega\) يغذي حملًا \(5\,\Omega\). حوّله إلى الصيغة التيارية.
  1. Calculate equivalent current; retain the resistance.
    احسب تيار المكافئ وأبقِ المقاومة.
    \[\begin{aligned}I_s&=\frac{V_s}{R_s}=\frac{10}{5}=2\,\mathrm A\\[8pt]R_{\parallel}&=5\,\Omega\end{aligned}\]
  2. Orient the current arrow toward the originally positive output terminal.
    وجّه سهم مصدر التيار نحو طرف الخرج الموجب الأصلي.
    \[V_{\mathrm{oc}}=I_sR_s=2(5)=10\,\mathrm V\]
  3. With equal parallel resistances the source current splits equally.
    مع تساوي المقاومتين المتوازيتين ينقسم تيار المصدر بالتساوي.
    \[\begin{aligned}I_L&=\frac{2(5)}{5+5}=1\,\mathrm A\\[8pt]V_L&=1(5)=5\,\mathrm V\end{aligned}\]
  4. Check the load result against the original circuit. Terminal equivalence does not imply identical internal behavior.
    تحقق من نتيجة الحمل بالدارة الأصلية. تكافؤ الطرفين لا يعني تماثل السلوك الداخلي.
    \[\begin{aligned}I_{L,\mathrm{original}}&=\frac{10}{5+5}=1\,\mathrm A\\[8pt]V_L&=5\,\mathrm V\end{aligned}\]
1975 · computer-oriented formulation

Matrix solution and modified nodal analysis (MNA)

الحل المصفوفي والتحليل العقدي المعدل

Matrix mathematics predates electronic computers. Ho, Ruehli and Brennan’s 1975 MNA paper is a specific documented milestone, not the birth of all computer circuit analysis. It adds selected branch currents to node voltages.
الرياضيات المصفوفية أقدم من الحواسيب الإلكترونية. بحث هو ورويلي وبرينان عام 1975 محطة موثقة للتحليل العقدي المعدل وليس بداية جميع حلول الدارات بالحاسوب. يضيف تيارات فروع مختارة إلى جهود العقد.
Why use it / advantage: Automated equation assembly; handles voltage sources directly.
الفائدة / الميزة: بناء آلي للمعادلات ومعالجة مباشرة لمصادر الجهد.
Limitation: Needs a correct model and reference; singular or poorly conditioned matrices require diagnosis. Nonlinear DC circuits need iterative methods beyond this linear example.
القيد / العيب: يحتاج نموذجًا صحيحًا ومرجعًا؛ المصفوفات المنفردة أو السيئة التكييف تحتاج تشخيصًا. الدارات المستمرة غير الخطية تحتاج طرقًا تكرارية تتجاوز هذا المثال الخطي.

MNA — theory and direct application to one circuit

Instead of separating all the theory from its example, each step below states one rule and immediately applies it to the same circuit. We solve it only once, ending with the matrix and its verification.

التحليل العقدي المعدل — النظرية والتطبيق مباشرة على دارة واحدة

ترد بعد كل قاعدة نظرية مباشرة طريقة تطبيقها على الدارة نفسها. سنبني المعادلات بالتدرج، ثم نشكل المصفوفة ونحلها مرة واحدة ونتحقق من النتيجة دون تكرار.

+− 12 V 4 Ω 6 Ω3 Ω S A VS VA 0 V (reference) IV
MNA unknowns: node voltages \(V_S\), \(V_A\), and source current \(I_V\) directed from S to ground. مجاهيل التحليل العقدي المعدل: جهدا العقدتين \(V_S\) و\(V_A\)، وتيار المنبع \(I_V\) باتجاه مرجعي مفترض من S نحو الأرضي.

Given: A \(12\,\mathrm V\) ideal voltage source joins node S to reference node B; a \(4\,\Omega\) resistor joins S to A; two resistors \(6\,\Omega\) and \(3\,\Omega\) join A to B. The direction chosen for \(I_V\) is from S toward B through the source.

معطيات الدارة: منبع جهد مثالي \(12\,\mathrm V\) بين العقدة S والعقدة المرجعية B؛ مقاومة \(4\,\Omega\) بين S وA؛ ومقاومتان \(6\,\Omega\) و\(3\,\Omega\) بين A وB. اخترنا اتجاه \(I_V\) من S نحو B عبر المنبع.

  1. Theory — choose reference and unknowns: Take B as zero volts. In MNA the unknowns are all non-reference node voltages plus one current through each ideal voltage source. Keep their order fixed throughout.
    النظرية — اختيار المرجع والمجاهيل: نختار B مرجعا للجهد. في MNA نضع جهود العقد غير المرجعية وتيارا مجهولا لكل منبع جهد مثالي، ونثبت ترتيبها في جميع المعادلات.
    Applied here: Two node voltages \(V_S\), \(V_A\), and one source current \(I_V\); the indicated purple symbols correspond to these unknowns.
    التطبيق على الدارة: يوجد جهدا عقدتين \(V_S\) و\(V_A\) وتيار منبع واحد \(I_V\). تظهر المجهولات على الرسم.
    \[V_B=0,\qquad \boldsymbol{x}=\begin{bmatrix}V_S\\V_A\\I_V\end{bmatrix}\]
  2. Theory — convert each resistor to conductance: In the matrix, a resistor enters as its conductance \(g=1/R\), not as the numerical resistance. Conductance is measured in siemens (S).
    النظرية — تحويل المقاومات إلى موصليات: تدخل المقاومة في المصفوفة بقيمة موصليتها \(g=1/R\)، وليس بقيمة المقاومة نفسها. وحدة الموصلية هي السيمنز (S).
    Applied here: The \(4\,\Omega\) branch is between S and A, while \(6\,\Omega\) and \(3\,\Omega\) are connected from A to reference B.
    التطبيق على الدارة: مقاومة \(4\,\Omega\) بين S وA، والمقاومتان \(6\,\Omega\) و\(3\,\Omega\) بين A والمرجع B.
    \[g_4=\frac14=0.25\,\mathrm S\]
    \[g_6=\frac16\,\mathrm S,\qquad g_3=\frac13\,\mathrm S\]
  3. Theory — KCL at each non-reference node: The current from node \(i\) through a resistor to node \(j\) is \((V_i-V_j)/R\). Include the assumed source current with its sign.
    النظرية — تطبيق قانون كيرشوف عند كل عقدة: يساوي التيار الخارج من العقدة \(i\) نحو العقدة \(j\) عبر مقاومة \((V_i-V_j)/R\). نضيف تيار منبع الجهد بإشارته وفق الاتجاه المفترض.
    Applied at S: One resistor goes to A and the assumed source current leaves S. Collect coefficients in the order \(V_S,V_A,I_V\). This is the first matrix row.
    التطبيق عند S: يتجه تيار المقاومة نحو A، ويخرج تيار المنبع المفترض من S. نجمع معاملات \(V_S,V_A,I_V\) بهذا الترتيب، فنحصل على الصف الأول.
    \[\frac{V_S-V_A}{4}+I_V=0\]
    \[0.25V_S-0.25V_A+1I_V=0\]
    Applied at A: Three resistor currents leave A, towards S and twice towards B. There is no voltage-source branch at A, hence the coefficient of \(I_V\) is zero. The coefficient of \(V_A\) is the sum of all three conductances.
    التطبيق عند A: تخرج ثلاثة تيارات مقاومية من A، أحدها نحو S واثنان نحو B. لا يتصل منبع الجهد مباشرة بالعقدة A، لذلك معامل \(I_V\) صفر. أما معامل \(V_A\) فهو مجموع موصليات المقاومات الثلاث.
    \[\frac{V_A-V_S}{4}+\frac{V_A}{6}+\frac{V_A}{3}=0\]
    \[\frac14+\frac16+\frac13=\frac34=0.75\,\mathrm S\]
    \[-0.25V_S+0.75V_A+0I_V=0\]

    This is the second matrix row. The negative off-diagonal values arise from the shared \(4\,\Omega\) resistor between S and A.

    وهذا هو الصف الثاني. تظهر المعاملات السالبة خارج القطر بسبب المقاومة المشتركة \(4\,\Omega\) بين S وA.

  4. Theory — add each ideal voltage-source constraint: The voltage at the positive terminal minus that at the negative terminal equals the specified source voltage.
    النظرية — إضافة قيد كل منبع جهد مثالي: يساوي جهد الطرف الموجب ناقص جهد الطرف السالب قيمة جهد المنبع.
    Applied here: The source positive pole is S and its negative pole is the reference B at zero volts. The resulting coefficients form the third matrix row.
    التطبيق على الدارة: الطرف الموجب عند S والسالب عند B المرجعية ذات الجهد الصفري. نحصل على الصف الثالث.
    \[V_S-V_B=12\,\mathrm V\quad\Longrightarrow\quad V_S=12\,\mathrm V\]
    \[1V_S+0V_A+0I_V=12\]
  5. From the general block form to the numerical matrix

    Use the fixed node order S, A and one voltage-source current. We now fill each block of the general form using the circuit values already derived.

    من الشكل العام إلى المصفوفة العددية خطوة بخطوة

    نثبت ترتيب العقدتين S ثم A، يليهما تيار منبع الجهد. نعوض الآن كل كتلة في الشكل العام بالقيم المستخرجة من الدارة في الخطوات السابقة.

    \[\begin{bmatrix}\boldsymbol G&\boldsymbol B\\\boldsymbol B^{\mathsf T}&\boldsymbol 0\end{bmatrix}\begin{bmatrix}\boldsymbol v\\\boldsymbol i_V\end{bmatrix}=\begin{bmatrix}\boldsymbol j\\\boldsymbol e\end{bmatrix}\]

    1. Fix the unknowns and block sizes

    There are two unknown node voltages and one unknown source current. Thus \(\boldsymbol G\) is \(2\times2\), \(\boldsymbol B\) is \(2\times1\), \(\boldsymbol B^{\mathsf T}\) is \(1\times2\), and the lower-right zero block is \(1\times1\). The superscript \(\mathsf T\) means transpose: turn the column into a row without changing its entries.

    1. تحديد المجاهيل وأبعاد الكتل

    لدينا جهدا عقدتين مجهولان وتيار منبع واحد مجهول. لذلك أبعاد \(\boldsymbol G\) هي \(2\times2\)، وأبعاد \(\boldsymbol B\) هي \(2\times1\)، وأبعاد \(\boldsymbol B^{\mathsf T}\) هي \(1\times2\)، والكتلة الصفرية السفلية أبعادها \(1\times1\). الرمز \(\mathsf T\) يعني النقل: تحويل العمود إلى صف مع الحفاظ على ترتيب عناصره.

    \[\boldsymbol v=\begin{bmatrix}V_S\\V_A\end{bmatrix},\qquad \boldsymbol i_V=\begin{bmatrix}I_V\end{bmatrix},\qquad \begin{bmatrix}\boldsymbol v\\\boldsymbol i_V\end{bmatrix}=\begin{bmatrix}V_S\\V_A\\I_V\end{bmatrix}\]

    2. Fill the conductance block \(\boldsymbol G\)

    Each diagonal entry is the sum of conductances connected to its node. Each off-diagonal entry is minus the conductance directly connecting the two nodes. S is connected through \(4\,\Omega\) to A. A is connected through \(4\,\Omega\) to S and through \(6\,\Omega\) and \(3\,\Omega\) to reference B. The ideal voltage source is represented separately by the source-connection block.

    2. التعويض داخل كتلة الموصلية \(\boldsymbol G\)

    كل عنصر قطري يساوي مجموع موصليات المقاومات المتصلة بعقدته. وكل عنصر خارج القطر يساوي سالب موصلية المقاومة الواصلة مباشرة بين العقدتين. تتصل S مع A عبر \(4\,\Omega\)، وتتصل A مع S عبر \(4\,\Omega\) ومع العقدة المرجعية B عبر \(6\,\Omega\) و\(3\,\Omega\). نمثل منبع الجهد المثالي في كتلة اتصال المنبع بصورة منفصلة.

    \[G_{11}=\frac14=0.25\,\mathrm S\]
    \[G_{12}=G_{21}=-\frac14=-0.25\,\mathrm S\]
    \[G_{22}=\frac14+\frac16+\frac13=\frac34=0.75\,\mathrm S\]
    \[\boldsymbol G=\begin{bmatrix}G_{11}&G_{12}\\G_{21}&G_{22}\end{bmatrix}=\begin{bmatrix}\frac14&-\frac14\\-\frac14&\frac14+\frac16+\frac13\end{bmatrix}=\begin{bmatrix}0.25&-0.25\\-0.25&0.75\end{bmatrix}\,\mathrm S\]

    3. Fill \(\boldsymbol B\) and its transpose

    The assumed \(I_V\) leaves node S through the source, so its coefficient in the S equation is \(+1\). No voltage-source branch touches A, so its coefficient there is \(0\). The source positive terminal is S and its negative terminal is reference B; its voltage constraint is \(V_S-0=12\). Bold \(\boldsymbol B\) denotes a matrix; plain B denotes the reference node.

    3. التعويض داخل \(\boldsymbol B\) ومنقولها

    اخترنا \(I_V\) خارجا من S عبر المنبع، لذلك معامله في معادلة S هو \(+1\). لا يتصل فرع منبع الجهد بالعقدة A، لذلك معامله في معادلتها صفر. الطرف الموجب للمنبع عند S والسالب عند العقدة المرجعية B، ومن ثم قيد الجهد هو \(V_S-0=12\). نميز بين الرمز الغامق \(\boldsymbol B\) للمصفوفة، والحرف B لاسم العقدة المرجعية.

    \[\boldsymbol B=\begin{bmatrix}1\\0\end{bmatrix}\quad\Longrightarrow\quad\boldsymbol B^{\mathsf T}=\begin{bmatrix}1&0\end{bmatrix}\]

    4. Fill the lower-right block and right-hand side

    The ideal source fixes its voltage independently of \(I_V\), so the coefficient of \(I_V\) in the source constraint is zero. There are no independent current sources injecting current into S or A, so both entries of \(\boldsymbol j\) are zero; resistor currents are already included in \(\boldsymbol G\). The single source voltage gives the single entry of \(\boldsymbol e\).

    4. التعويض في الكتلة السفلية اليمنى والطرف الأيمن

    يفرض منبع الجهد المثالي جهده مستقلا عن \(I_V\)، لذلك معامل \(I_V\) في قيد المنبع صفر. ولا توجد منابع تيار مستقلة تحقن تيارا في S أو A، فتكون مركبتا \(\boldsymbol j\) صفرا؛ أما تيارات المقاومات فقد مثلناها بالفعل داخل \(\boldsymbol G\). جهد المنبع الوحيد يعطينا العنصر الوحيد في \(\boldsymbol e\).

    \[\boldsymbol 0=\begin{bmatrix}0\end{bmatrix},\qquad\boldsymbol j=\begin{bmatrix}0\\0\end{bmatrix}\,\mathrm A,\qquad\boldsymbol e=\begin{bmatrix}12\end{bmatrix}\,\mathrm V\]

    5. Put each numerical block in its original position

    The upper-left block contains the four conductance values; the last column above the line is the source-connection column. The last row to the left of the vertical line is its transpose. The lower-right corner is zero. The dividing lines below show block boundaries only.

    5. وضع كل كتلة عددية في مكانها من الشكل العام

    نضع قيم الموصلية الأربع أعلى اليسار، وعمود اتصال المنبع أعلى اليمين. نضع منقول عمود الاتصال أسفل اليسار، ثم الصفر في الركن السفلي الأيمن. الخطان في المصفوفة التالية يوضحان حدود الكتل فقط.

    \[\left[\begin{array}{cc|c}0.25&-0.25&1\\-0.25&0.75&0\\\hline 1&0&0\end{array}\right]\left[\begin{array}{c}V_S\\V_A\\\hline I_V\end{array}\right]=\left[\begin{array}{c}0\\0\\\hline12\end{array}\right]\]

    Removing those dividing lines gives the numerical system built above. Numerical values are entered using amperes, volts and siemens; the first two rows express current balance in amperes, and the last row expresses the source constraint in volts.

    بحذف خطوط فصل الكتل نحصل على النظام العددي الذي بنيناه أعلاه. ندخل القيم باستخدام الأمبير والفولت والسيمنز؛ يمثل الصفان الأول والثاني توازن التيارات بالأمبير، ويمثل الصف الأخير قيد جهد المنبع بالفولت.

    \[\underbrace{\begin{bmatrix}0.25&-0.25&1\\-0.25&0.75&0\\1&0&0\end{bmatrix}}_{\boldsymbol A}\underbrace{\begin{bmatrix}V_S\\V_A\\I_V\end{bmatrix}}_{\boldsymbol x}=\underbrace{\begin{bmatrix}0\\0\\12\end{bmatrix}}_{\boldsymbol b}\]

    6. Check the substitution by multiplying each row

    Multiply each row by the unknown column in the fixed order \(V_S,V_A,I_V\). This recovers the same two KCL equations and the source constraint derived from the circuit. Here \(\boldsymbol A\) is the assembled coefficient matrix, \(\boldsymbol x\) the unknown vector, and \(\boldsymbol b\) the assembled right-hand side.

    6. التحقق من التعويض بضرب كل صف

    نضرب عناصر كل صف بمركبات عمود المجاهيل بالترتيب الثابت \(V_S,V_A,I_V\). فنستعيد معادلتي كيرشوف وقيد المنبع اللذين اشتققناهما من الدارة. هنا \(\boldsymbol A\) مصفوفة المعاملات الكاملة، و\(\boldsymbol x\) متجه المجاهيل، و\(\boldsymbol b\) متجه الطرف الأيمن الكامل.

    \[\begin{aligned}\text{Row 1:}\quad&0.25V_S-0.25V_A+1I_V=0\\[5pt]\text{Row 2:}\quad&-0.25V_S+0.75V_A+0I_V=0\\[5pt]\text{Row 3:}\quad&1V_S+0V_A+0I_V=12\end{aligned}\]
  6. Theory — solve and verify: Solve the linear equations in a convenient order, then substitute the values back into KCL and the source constraint.
    النظرية — حل النظام والتحقق: نحل المعادلات الخطية بترتيب مناسب، ثم نعوض النتائج في قانون كيرشوف وقيد المنبع للتحقق.
    Applied here: Row 3 gives \(V_S\). Insert it in row 2 to find \(V_A\), then in row 1 to find \(I_V\). The negative current means that the actual source current flows opposite to its assumed direction.
    التطبيق على الدارة: يعطينا الصف الثالث \(V_S\)، ثم نعوضه في الثاني لإيجاد \(V_A\)، ثم في الأول لإيجاد \(I_V\). تعني الإشارة السالبة أن تيار المنبع الحقيقي يعاكس الاتجاه المرجعي المفترض.
    \[V_S=12\,\mathrm V\]
    \[-0.25(12)+0.75V_A=0\quad\Longrightarrow\quad V_A=4\,\mathrm V\]
    \[0.25(12)-0.25(4)+I_V=0\quad\Longrightarrow\quad I_V=-2\,\mathrm A\]
    Verification: At A, \((4-12)/4+4/6+4/3=0\); at S, \((12-4)/4-2=0\); and the source fixes \(V_S=12\,\mathrm V\). All three equations hold.
    التحقق: عند A نجد \((4-12)/4+4/6+4/3=0\)، وعند S نجد \((12-4)/4-2=0\)، وقيد المنبع يعطي \(V_S=12\,\mathrm V\). تحققت المعادلات الثلاث.
    \[\boxed{V_S=12\,\mathrm V,\qquad V_A=4\,\mathrm V,\qquad I_V=-2\,\mathrm A}\]

Numerical implementation: A computer should solve the matrix system directly, without forming an explicit matrix inverse. The same three rows can be entered in MATLAB or Python.

التطبيق البرمجي: نحل النظام المصفوفي مباشرة بالحاسوب دون حساب معكوس المصفوفة صراحة. يمكن إدخال الصفوف الثلاثة نفسها في MATLAB أو Python.

G = [0.25 -0.25 1; -0.25 0.75 0; 1 0 0];
b = [0; 0; 12];
x = G\b;

Second worked example — three voltage sources and one current source

Apply modified nodal analysis (MNA) to the supplied circuit, keeping every voltage source explicitly in the full matrix. Then reduce the equations to the two upper-node voltages and verify the answer.

مثال ثان محلول بالتفصيل — ثلاثة منابع جهد ومنبع تيار

نطبق التحليل العقدي المعدل على الدارة المرفقة، مع تمثيل كل منبع جهد صراحة في المصفوفة الكاملة. ثم نختزل المعادلات إلى جهدي العقدتين العلويتين ونتحقق من الحل.

Second MNA example with separated circuit labelsR1 1 ohm connects A to C1, R2 2 ohms connects A to C2, R3 3 ohms connects A to B, and R4 4 ohms connects B to C3. E1 is positive at C1, E2 is negative at C2, and E3 is positive at C3. A 10 ampere current source injects current upward into B. All source lower terminals connect to reference node 0.+−−++−A: VAB: VBR₃ = 3 Ω0: reference / المرجعR₁ = 1 ΩR₂ = 2 ΩR₄ = 4 ΩE₁ = 10 VE₂ = 5 VE₃ = 6 VJ = 10 AC₁: V₁ = 10 VC₂: V₂ = −5 VC₃: V₃ = 6 VI₁I₂I₄I₃
Redrawn from the supplied circuit. Blue arrows are assumed resistor-current directions; purple labels identify the intermediate nodes needed for full MNA.
إعادة رسم الدارة المرفقة. الأسهم الزرقاء اتجاهات مفترضة لتيارات المقاومات، والرموز البنفسجية تعرف العقد الوسيطة اللازمة للتحليل العقدي المعدل الكامل.

1. Read the values and polarities before writing equations

The long battery plate is positive in the original drawing. E₁ and E₃ are positive at the top; E₂ is positive at the bottom. All three lower terminals share reference node 0. The current source injects 10 A upward into B. E₂ has a positive magnitude of 5 V, but its upper node is at −5 V because of its polarity.

1. قراءة القيم والقطبيات قبل كتابة المعادلات

الخط الأطول في رمز البطارية هو الطرف الموجب في الرسم الأصلي. الطرف العلوي موجب في المنبعين الأول والثالث، بينما الطرف السفلي موجب في المنبع الثاني. نختار السلك السفلي المشترك عقدة مرجعية 0. يحقن منبع التيار 10 أمبير إلى الأعلى في B. مقدار المنبع الثاني موجب ويساوي 5 فولت، لكن جهد عقدته العلوية يساوي −5 فولت بسبب قطبيته.

\[R_1=1\,\Omega,\quad R_2=2\,\Omega,\quad R_3=3\,\Omega,\quad R_4=4\,\Omega\]
\[V_0=0,\qquad V_1=+10\,\mathrm V,\qquad V_2=-5\,\mathrm V,\qquad V_3=+6\,\mathrm V,\qquad J=10\,\mathrm A\]

2. Choose the full MNA unknown vector

Besides A and B, include the intermediate nodes C₁, C₂, C₃ between each vertical resistor and its voltage source. Use \(V_1,V_2,V_3\) for their voltages. Define source currents \(I_{E1},I_{E2},I_{E3}\) downward from the intermediate nodes to reference, including for the reversed source E₂. These are algebraic reference directions, not assumptions about the actual flow.

2. اختيار متجه المجاهيل الكامل

بالإضافة إلى A وB، ندرج العقد الوسيطة C₁ وC₂ وC₃ بين كل مقاومة عمودية ومنبع الجهد أسفلها، ونرمز لجهودها بـ \(V_1,V_2,V_3\). نفترض تيارات المنابع \(I_{E1},I_{E2},I_{E3}\) نحو الأسفل من العقد الوسيطة إلى المرجع، بما فيها المنبع المعكوس E₂. هذه اتجاهات مرجعية جبرية ولا تشترط أن تكون اتجاهات التيار الحقيقية.

\[\boldsymbol v=\begin{bmatrix}V_A\\V_B\\V_1\\V_2\\V_3\end{bmatrix},\quad\boldsymbol i_E=\begin{bmatrix}I_{E1}\\I_{E2}\\I_{E3}\end{bmatrix},\quad\boldsymbol x=\begin{bmatrix}\boldsymbol v\\\boldsymbol i_E\end{bmatrix}\]

There are five non-reference node voltages and three source currents: eight unknowns. Thus \(\boldsymbol G\) is \(5\times5\), \(\boldsymbol B\) is \(5\times3\), and the full system is \(8\times8\). Bold \(\boldsymbol B\) denotes the connection matrix, whereas plain B is the upper-right node.

لدينا خمسة جهود عقد غير مرجعية وثلاثة تيارات منابع، أي ثمانية مجاهيل. لذلك أبعاد \(\boldsymbol G\) هي \(5\times5\)، وأبعاد \(\boldsymbol B\) هي \(5\times3\)، وأبعاد النظام الكامل \(8\times8\). الرمز الغامق \(\boldsymbol B\) مصفوفة الاتصال، أما الحرف B فهو اسم العقدة العلوية اليمنى.

3. Write KCL at each of the five nodes

Use currents leaving a node through resistors and voltage sources on the left; put independent current injections on the right. In the fixed node order A, B, C₁, C₂, C₃, this gives:

3. كتابة قانون كيرشوف عند العقد الخمس

نضع التيارات الخارجة عبر المقاومات ومنابع الجهد في الطرف الأيسر، والتيارات المحقونة من منابع التيار المستقلة في الطرف الأيمن. وبترتيب العقد الثابت A ثم B ثم C₁ ثم C₂ ثم C₃ نحصل على:

\[\text{A:}\quad\frac{V_A-V_1}{1}+\frac{V_A-V_2}{2}+\frac{V_A-V_B}{3}=0\]
\[\text{B:}\quad\frac{V_B-V_A}{3}+\frac{V_B-V_3}{4}=10\]
\[\text{C}_1:\quad\frac{V_1-V_A}{1}+I_{E1}=0\]
\[\text{C}_2:\quad\frac{V_2-V_A}{2}+I_{E2}=0\]
\[\text{C}_3:\quad\frac{V_3-V_B}{4}+I_{E3}=0\]

4. Build the conductance block entry by entry

A diagonal entry sums conductances connected to that node. An off-diagonal entry is the negative conductance directly connecting the corresponding two nodes; it is zero when no resistor directly joins them.

4. بناء كتلة الموصلية عنصرا عنصرا

العنصر القطري هو مجموع موصليات المقاومات المتصلة بالعقدة. والعنصر خارج القطر هو سالب موصلية المقاومة الواصلة مباشرة بين العقدتين؛ ويساوي صفرا عند عدم وجود مقاومة مباشرة بينهما.

\[g_1=\frac1{R_1}=1,\quad g_2=\frac1{R_2}=\frac12,\quad g_3=\frac1{R_3}=\frac13,\quad g_4=\frac1{R_4}=\frac14\quad(\mathrm S)\]
\[G_{AA}=g_1+g_2+g_3=\frac{11}{6},\qquad G_{BB}=g_3+g_4=\frac7{12}\]
\[G_{C_1C_1}=g_1=1,\qquad G_{C_2C_2}=g_2=\frac12,\qquad G_{C_3C_3}=g_4=\frac14\]
\[G_{AB}=G_{BA}=-\frac13,\quad G_{AC_1}=G_{C_1A}=-1\]
\[G_{AC_2}=G_{C_2A}=-\frac12,\quad G_{BC_3}=G_{C_3B}=-\frac14\]

Every other off-diagonal entry is zero. With the same five-node order for both rows and columns, the numerical conductance block is:

جميع العناصر الأخرى خارج القطر تساوي صفرا. نعتمد ترتيب العقد الخمس نفسه للصفوف والأعمدة، فتكون كتلة الموصلية العددية:

\[\boldsymbol G=\begin{bmatrix}\frac{11}{6}&-\frac13&-1&-\frac12&0\\-\frac13&\frac7{12}&0&0&-\frac14\\-1&0&1&0&0\\-\frac12&0&0&\frac12&0\\0&-\frac14&0&0&\frac14\end{bmatrix}\,\mathrm S\]

5. Build \(\boldsymbol B\), the source constraints and the right-hand side

Each source current leaves its own intermediate node, giving a +1 in that node's row and that source's column. No source current is directly connected to A or B, so the first two rows are zero. Because all three current directions were chosen from the intermediate nodes toward reference, the second column still contains +1: E₂'s reversed polarity is represented by −5 in \(\boldsymbol e\).

5. بناء \(\boldsymbol B\) وقيود المنابع والطرف الأيمن

يخرج تيار كل منبع من عقدته الوسيطة، فنضع +1 في صف تلك العقدة وعمود ذلك المنبع. ولا يتصل أي تيار منبع جهد مباشرة بالعقدتين A وB، لذلك الصفان الأولان صفريان. بما أننا اخترنا اتجاهات التيارات الثلاثة من العقد الوسيطة نحو المرجع، يبقى العنصر في العمود الثاني +1؛ ونمثل قطبية المنبع الثاني المعكوسة بالقيمة −5 داخل \(\boldsymbol e\).

\[\boldsymbol B=\begin{bmatrix}0&0&0\\0&0&0\\1&0&0\\0&1&0\\0&0&1\end{bmatrix},\quad\boldsymbol B^{\mathsf T}=\begin{bmatrix}0&0&1&0&0\\0&0&0&1&0\\0&0&0&0&1\end{bmatrix}\]
\[\boldsymbol B^{\mathsf T}\boldsymbol v=\boldsymbol e\quad\Longleftrightarrow\quad V_1=10,\quad V_2=-5,\quad V_3=6\]
\[\boldsymbol j=\begin{bmatrix}0\\10\\0\\0\\0\end{bmatrix}\,\mathrm A,\qquad\boldsymbol e=\begin{bmatrix}10\\-5\\6\end{bmatrix}\,\mathrm V\]

The lower-right block is a 3×3 zero matrix because these independent ideal voltage-source constraints contain no source-current term. The only nonzero current injection is +10 A at B.

الكتلة السفلية اليمنى مصفوفة أصفار أبعادها 3×3، لأن قيود منابع الجهد المثالية المستقلة هنا لا تحتوي على معاملات لتياراتها. أما حقن التيار الوحيد غير الصفري فهو +10 أمبير عند B.

6. Substitute all blocks into the general form

Keep the unknown order unchanged. Horizontal and vertical dividing lines identify the block boundaries. On a narrow screen, scroll horizontally inside the equation.

6. التعويض بجميع الكتل داخل الشكل العام

نحافظ على ترتيب المجاهيل نفسه. يوضح الخطان الأفقي والعمودي حدود الكتل. على الشاشة الضيقة يمكن تمرير المعادلة أفقيا داخل إطارها.

\[\begin{bmatrix}\boldsymbol G&\boldsymbol B\\\boldsymbol B^{\mathsf T}&\boldsymbol0_{3\times3}\end{bmatrix}\begin{bmatrix}\boldsymbol v\\\boldsymbol i_E\end{bmatrix}=\begin{bmatrix}\boldsymbol j\\\boldsymbol e\end{bmatrix}\]
\[\left[\begin{array}{ccccc|ccc}\frac{11}{6}&-\frac13&-1&-\frac12&0&0&0&0\\-\frac13&\frac7{12}&0&0&-\frac14&0&0&0\\-1&0&1&0&0&1&0&0\\-\frac12&0&0&\frac12&0&0&1&0\\0&-\frac14&0&0&\frac14&0&0&1\\\hline0&0&1&0&0&0&0&0\\0&0&0&1&0&0&0&0\\0&0&0&0&1&0&0&0\end{array}\right]\begin{bmatrix}V_A\\V_B\\V_1\\V_2\\V_3\\I_{E1}\\I_{E2}\\I_{E3}\end{bmatrix}=\left[\begin{array}{c}0\\10\\0\\0\\0\\\hline10\\-5\\6\end{array}\right]\]

Rows 1–5 are KCL at A, B, C₁, C₂, C₃; rows 6–8 are the three voltage constraints. Numerical values use amperes, volts and siemens. The first five equations have current units; the last three have voltage units.

الصفوف من 1 إلى 5 هي قانون كيرشوف عند A وB وC₁ وC₂ وC₃، والصفوف من 6 إلى 8 هي قيود الجهد الثلاثة. ندخل القيم بالأمبير والفولت والسيمنز. وحدات المعادلات الخمس الأولى وحدات تيار، ووحدات المعادلات الثلاث الأخيرة وحدات جهد.

7. Solve by substituting the known source-node voltages

Rows 6–8 immediately give V₁, V₂ and V₃. Substitute these into rows 1 and 2; this reduces the full MNA system to two equations without changing its solution.

7. الحل بالتعويض بجهود عقد المنابع المعلومة

تعطي الصفوف من 6 إلى 8 مباشرة جهود العقد الوسيطة. نعوضها في الصفين الأول والثاني، فنختزل نظام التحليل العقدي المعدل الكامل إلى معادلتين لهما الحل نفسه.

\[(V_A-10)+\frac{V_A-(-5)}2+\frac{V_A-V_B}3=0\]
\[\left(1+\frac12+\frac13\right)V_A-\frac13V_B=10-\frac52=\frac{15}{2}\]
\[\frac{V_B-V_A}3+\frac{V_B-6}4=10\quad\Longrightarrow\quad-\frac13V_A+\frac7{12}V_B=10+\frac64=\frac{23}{2}\]
\[\begin{bmatrix}\frac{11}{6}&-\frac13\\-\frac13&\frac7{12}\end{bmatrix}\begin{bmatrix}V_A\\V_B\end{bmatrix}=\begin{bmatrix}\frac{15}{2}\\\frac{23}{2}\end{bmatrix}\]

Multiply the first equation by 6 and the second by 12 to remove fractions.

نضرب المعادلة الأولى بـ 6 والثانية بـ 12 لإزالة الكسور.

\[11V_A-2V_B=45,\qquad-4V_A+7V_B=138\]

For a direct elimination of V_B, multiply the first equation by 7 and the second by 2, then add:

لحذف جهد العقدة B مباشرة، نضرب المعادلة الأولى بـ 7 والثانية بـ 2، ثم نجمع:

\[77V_A-14V_B=315,\qquad-8V_A+14V_B=276\]
\[69V_A=591\quad\Longrightarrow\quad V_A=\frac{197}{23}\approx8.5652\,\mathrm V\]
\[V_B=\frac{11V_A-45}{2}=\frac{11(197/23)-45}{2}=\frac{566}{23}\approx24.6087\,\mathrm V\]

8. Find resistor and voltage-source currents

Use the blue reference arrows: I₁, I₂ and I₄ downward; I₃ from A to B. In each vertical branch, the resistor and its voltage source carry the same current. A negative result means flow opposite to the reference arrow.

8. حساب تيارات المقاومات ومنابع الجهد

نعتمد الأسهم الزرقاء: التيارات الأول والثاني والرابع نحو الأسفل، والثالث من A إلى B. يمر التيار نفسه في المقاومة ومنبع الجهد المتصل معها على التوالي في كل فرع عمودي. تعني النتيجة السالبة أن التيار الحقيقي يعاكس السهم المرجعي.

\[I_1=I_{E1}=\frac{V_A-10}{1}=-\frac{33}{23}\approx-1.4348\,\mathrm A\]
\[I_2=I_{E2}=\frac{V_A+5}{2}=\frac{156}{23}\approx6.7826\,\mathrm A\]
\[I_3=\frac{V_A-V_B}{3}=-\frac{123}{23}\approx-5.3478\,\mathrm A\]
\[I_4=I_{E3}=\frac{V_B-6}{4}=\frac{107}{23}\approx4.6522\,\mathrm A\]

Thus I₁ actually flows upward and I₃ flows from B to A. I₂ and I₄ flow downward. The complete solution, in the original unknown order, is:

إذن يتجه التيار الأول فعليا نحو الأعلى، ويتجه التيار الثالث من B إلى A، بينما يتجه التياران الثاني والرابع نحو الأسفل. وبترتيب المجاهيل الأصلي يكون الحل الكامل:

\[\boldsymbol x=\begin{bmatrix}\frac{197}{23}\\\frac{566}{23}\\10\\-5\\6\\-\frac{33}{23}\\\frac{156}{23}\\\frac{107}{23}\end{bmatrix}\]

9. Verify KCL, source constraints and power balance

At A the signed sum of the three outgoing currents is zero. At B the two outgoing resistor currents equal the 10 A injection.

9. التحقق من كيرشوف وقيود المنابع وتوازن الاستطاعة

عند A يساوي المجموع الجبري للتيارات الثلاثة الخارجة صفرا. وعند B يساوي مجموع تياري المقاومتين الخارجين تيار الحقن البالغ 10 أمبير.

\[I_1+I_2+I_3=\frac{-33+156-123}{23}=0\]
\[-I_3+I_4=\frac{123+107}{23}=10\,\mathrm A\]
\[V_1-V_0=10\,\mathrm V,\qquad V_0-V_2=5\,\mathrm V,\qquad V_3-V_0=6\,\mathrm V\]

For power, use the passive sign convention: positive means absorbed power. Resistors absorb \(I^2R\). For voltage sources, multiply voltage by current entering the positive terminal. E₂'s downward current enters its negative terminal, and the upward current-source current enters its lower terminal.

لحساب الاستطاعة نعتمد اصطلاح الإشارة المستهلكة: الإشارة الموجبة تعني امتصاص الاستطاعة. تمتص المقاومات \(I^2R\). وفي منابع الجهد نضرب الجهد بالتيار الداخل إلى الطرف الموجب. يدخل التيار المرجعي الهابط للمنبع الثاني من طرفه السالب، ويدخل تيار منبع التيار الصاعد من طرفه السفلي.

Resistor power — substitute, square the current, then multiply by resistance

In \(P_{Rk}=I_k^2R_k\), \(P_{Rk}\) is the power absorbed by resistor \(R_k\), \(I_k\) is its current, and \(k\) identifies the resistor. Use current in amperes and resistance in ohms to obtain power in watts. Keep the exact current fractions until the final rounding. Squaring a negative current gives a positive value, so its sign does not make resistor power negative.

استطاعة المقاومات — التعويض ثم تربيع التيار ثم الضرب بالمقاومة

في العلاقة \(P_{Rk}=I_k^2R_k\)، تمثل \(P_{Rk}\) الاستطاعة التي تمتصها المقاومة \(R_k\)، ويمثل \(I_k\) تيارها، ويميز الدليل \(k\) رقم المقاومة. نعوض التيار بالأمبير والمقاومة بالأوم فنحصل على الاستطاعة بالواط. نستخدم الكسور الدقيقة للتيارات ونؤجل التقريب إلى النتيجة النهائية. يؤدي تربيع التيار السالب إلى قيمة موجبة؛ لذلك لا تجعل إشارة التيار استطاعة المقاومة سالبة.

\[P_{Rk}=I_k^2R_k,\qquad [P]=\mathrm A^2\cdot\Omega=\mathrm W\]

Resistor 1: Substitute its current and resistance, square the numerator and denominator, then multiply by the resistance.

المقاومة 1: نعوض تيارها ومقاومتها، ثم نربع البسط والمقام ونضرب بالمقاومة.

\[I_1=\frac{-33}{23}\,\mathrm A,\qquad R_1=1\,\Omega\]
\[\begin{aligned}P_{R1}&=I_1^{\,2}R_1\\[4pt]&=\left(\frac{-33}{23}\right)^2\times1\\[4pt]&=\frac{(-33)^2}{23^2}\times1\\[4pt]&=\frac{1089}{529}\times1\\[4pt]&=\frac{1089\times1}{529}\\[4pt]&=\frac{1089}{529}\\[4pt]&\approx\boxed{2.0586\,\mathrm W}\end{aligned}\]

Resistor 2: Substitute its current and resistance, square the numerator and denominator, then multiply by the resistance.

المقاومة 2: نعوض تيارها ومقاومتها، ثم نربع البسط والمقام ونضرب بالمقاومة.

\[I_2=\frac{156}{23}\,\mathrm A,\qquad R_2=2\,\Omega\]
\[\begin{aligned}P_{R2}&=I_2^{\,2}R_2\\[4pt]&=\left(\frac{156}{23}\right)^2\times2\\[4pt]&=\frac{(156)^2}{23^2}\times2\\[4pt]&=\frac{24336}{529}\times2\\[4pt]&=\frac{24336\times2}{529}\\[4pt]&=\frac{48672}{529}\\[4pt]&\approx\boxed{92.0076\,\mathrm W}\end{aligned}\]

Resistor 3: Substitute its current and resistance, square the numerator and denominator, then multiply by the resistance.

المقاومة 3: نعوض تيارها ومقاومتها، ثم نربع البسط والمقام ونضرب بالمقاومة.

\[I_3=\frac{-123}{23}\,\mathrm A,\qquad R_3=3\,\Omega\]
\[\begin{aligned}P_{R3}&=I_3^{\,2}R_3\\[4pt]&=\left(\frac{-123}{23}\right)^2\times3\\[4pt]&=\frac{(-123)^2}{23^2}\times3\\[4pt]&=\frac{15129}{529}\times3\\[4pt]&=\frac{15129\times3}{529}\\[4pt]&=\frac{45387}{529}\\[4pt]&\approx\boxed{85.7977\,\mathrm W}\end{aligned}\]

Resistor 4: Substitute its current and resistance, square the numerator and denominator, then multiply by the resistance.

المقاومة 4: نعوض تيارها ومقاومتها، ثم نربع البسط والمقام ونضرب بالمقاومة.

\[I_4=\frac{107}{23}\,\mathrm A,\qquad R_4=4\,\Omega\]
\[\begin{aligned}P_{R4}&=I_4^{\,2}R_4\\[4pt]&=\left(\frac{107}{23}\right)^2\times4\\[4pt]&=\frac{(107)^2}{23^2}\times4\\[4pt]&=\frac{11449}{529}\times4\\[4pt]&=\frac{11449\times4}{529}\\[4pt]&=\frac{45796}{529}\\[4pt]&\approx\boxed{86.5709\,\mathrm W}\end{aligned}\]

Source power — sign, substitution and interpretation

Use \(P=vi\) with the passive sign convention: \(i\) is the signed current entering the terminal marked positive for \(v\). Positive power means absorption; negative power means delivery. Unlike resistor power, source power does not square the current. Keep the signed current values.

استطاعة المنابع — الإشارة والتعويض وتفسير النتيجة

نستخدم \(P=vi\) وفق اصطلاح الإشارة المستهلكة: يمثل \(i\) التيار الجبري الداخل إلى الطرف الذي اخترناه موجبا للجهد \(v\). تعني الاستطاعة الموجبة امتصاص الطاقة، وتعني الاستطاعة السالبة تزويد الدارة بالطاقة. بخلاف حساب استطاعة المقاومة، لا نربع التيار عند حساب استطاعة المنبع، بل نحافظ على إشارته الجبرية.

\[P=vi,\qquad P>0:\ \text{absorbed},\qquad P<0:\ \text{delivered}\]

1. Voltage source \(E_1=10\,\mathrm V\)

Its upper terminal is positive. The downward reference current \(I_1\) enters that terminal, so \(P_{E1}=E_1I_1\). The computed negative \(I_1\) means the actual current flows upward and leaves the positive terminal.

1. منبع الجهد الأول \(E_1=10\,\mathrm V\)

طرفه العلوي موجب. يدخل التيار المرجعي الهابط \(I_1\) إلى هذا الطرف، لذلك \(P_{E1}=E_1I_1\). أما القيمة المحسوبة السالبة للتيار فتعني أن التيار الحقيقي يصعد ويخرج من الطرف الموجب.

\[\begin{aligned}P_{E1}&=E_1I_1\\[4pt]&=10\left(-\frac{33}{23}\right)\\[4pt]&=-\frac{10\times33}{23}\\[4pt]&=-\frac{330}{23}\\[4pt]&\approx\boxed{-14.3478\,\mathrm W}\end{aligned}\]

The result is negative: E₁ delivers approximately 14.3478 W to the circuit.

النتيجة سالبة: يزود المنبع الأول الدارة باستطاعة مقدارها نحو 14.3478 واط.

2. Reversed voltage source \(E_2=5\,\mathrm V\)

Its lower terminal is positive and its upper terminal is negative. The downward current \(I_2\) enters the negative terminal, so the current entering the positive terminal is \(-I_2\). Equivalently, the voltage drop in the downward current direction is \(V_2-V_0=-5\,\mathrm V\).

2. منبع الجهد الثاني المعكوس \(E_2=5\,\mathrm V\)

طرفه السفلي موجب وطرفه العلوي سالب. يدخل التيار الهابط \(I_2\) إلى الطرف السالب، لذلك التيار الداخل إلى الطرف الموجب هو \(-I_2\). وبصورة مكافئة، يساوي فرق الجهد باتجاه التيار الهابط \(V_2-V_0=-5\,\mathrm V\).

\[i_{+,E2}=-I_2=-\frac{156}{23}\,\mathrm A\]
\[\begin{aligned}P_{E2}&=E_2(-I_2)=-E_2I_2\\[4pt]&=-5\left(\frac{156}{23}\right)\\[4pt]&=-\frac{5\times156}{23}\\[4pt]&=-\frac{780}{23}\\[4pt]&\approx\boxed{-33.9130\,\mathrm W}\end{aligned}\]

The source magnitude is +5 V. The minus sign in the power formula comes from the relationship between its polarity and the chosen current direction. E₂ delivers approximately 33.9130 W.

مقدار جهد المنبع هو +5 فولت. تأتي الإشارة السالبة في صيغة الاستطاعة من علاقة قطبية المنبع باتجاه التيار المختار. يزود المنبع الثاني الدارة باستطاعة مقدارها نحو 33.9130 واط.

3. Voltage source \(E_3=6\,\mathrm V\)

Its upper terminal is positive. The downward \(I_4\) enters that positive terminal, so \(P_{E3}=E_3I_4\).

3. منبع الجهد الثالث \(E_3=6\,\mathrm V\)

طرفه العلوي موجب، ويدخل التيار الهابط \(I_4\) إلى هذا الطرف الموجب، لذلك \(P_{E3}=E_3I_4\).

\[\begin{aligned}P_{E3}&=E_3I_4\\[4pt]&=6\left(\frac{107}{23}\right)\\[4pt]&=\frac{6\times107}{23}\\[4pt]&=\frac{642}{23}\\[4pt]&\approx\boxed{+27.9130\,\mathrm W}\end{aligned}\]

The result is positive: E₃ absorbs approximately 27.9130 W. An ideal voltage source can absorb power as well as deliver it; its symbol alone does not determine the power direction.

النتيجة موجبة: يمتص المنبع الثالث استطاعة مقدارها نحو 27.9130 واط. يمكن لمنبع الجهد المثالي أن يمتص الاستطاعة أو يزودها؛ ولا يحدد رمز المنبع وحده اتجاه انتقال الطاقة.

4. Current source \(J=10\,\mathrm A\)

The arrow points upward from reference 0 to B, so the current enters the source at its lower terminal. To apply \(P=vi\) directly with \(i=J\), mark the lower terminal positive for the reference voltage \(v_J\). Thus \(v_J=V_0-V_B\), which is negative for this solution. This is a voltage reference choice; the upper terminal actually has the higher potential.

4. منبع التيار \(J=10\,\mathrm A\)

يشير السهم إلى الأعلى من المرجع 0 نحو B، فيدخل التيار إلى المنبع من طرفه السفلي. لتطبيق \(P=vi\) مباشرة مع \(i=J\)، نختار الطرف السفلي موجبا للجهد المرجعي \(v_J\). لذلك \(v_J=V_0-V_B\)، وتكون قيمته سالبة في هذا الحل. هذا اختيار مرجعي للجهد؛ أما الطرف العلوي فهو الأعلى جهدا فعليا.

\[v_J=V_0-V_B=0-\frac{566}{23}=-\frac{566}{23}\,\mathrm V\]
\[\begin{aligned}P_J&=v_JJ=(V_0-V_B)J\\[4pt]&=\left(0-\frac{566}{23}\right)\times10\\[4pt]&=-\frac{566\times10}{23}\\[4pt]&=-\frac{5660}{23}\\[4pt]&\approx\boxed{-246.0870\,\mathrm W}\end{aligned}\]

The negative result means the current source delivers approximately 246.0870 W.

تعني النتيجة السالبة أن منبع التيار يزود الدارة باستطاعة مقدارها نحو 246.0870 واط.

5. Sum the signed powers and check energy conservation

Add source powers with their signs, including the positive power absorbed by E₃. Use exact fractions for the balance; decimal rounding can leave a small apparent mismatch.

5. جمع الاستطاعات بإشاراتها والتحقق من حفظ الطاقة

نجمع استطاعات المنابع بإشاراتها، بما فيها الاستطاعة الموجبة التي يمتصها المنبع الثالث. نستخدم الكسور الدقيقة للتحقق، لأن تقريب القيم العشرية قد ينتج فرقا ظاهريا صغيرا.

\[\begin{aligned}\sum P_{\mathrm{sources}}&=P_{E1}+P_{E2}+P_{E3}+P_J\\[4pt]&=\frac{-330-780+642-5660}{23}\\[4pt]&=-\frac{6128}{23}\\[4pt]&\approx-266.4348\,\mathrm W\end{aligned}\]
\[\begin{aligned}\sum P_R&=\frac{1089+48672+45387+45796}{529}\\[4pt]&=\frac{140944}{529}=\frac{6128}{23}\\[4pt]&\approx266.4348\,\mathrm W\end{aligned}\]
\[\sum P=\sum P_R+\sum P_{\mathrm{sources}}=\frac{6128}{23}-\frac{6128}{23}=\boxed{0\,\mathrm W}\]

E₁, E₂ and the current source deliver power; E₃ absorbs power. The equations and the power balance both confirm the result.

يزود المنبعان الأول والثاني ومنبع التيار الدارة بالاستطاعة، بينما يمتص المنبع الثالث الاستطاعة. تؤكد معادلات الدارة وتوازن الاستطاعة صحة الحل.

10 review questions

10 أسئلة للمراجعة

1. Why distinguish 1826 from 1827 for Ohm?
لماذا نميز 1826 عن 1827 في تاريخ أوم؟
Paper versus comprehensive monograph.
بحث مقابل كتاب شامل.
2. When are two resistors truly in parallel?
متى تكون مقاومتان على التوازي فعلًا؟
They share the same two nodes.
عندما تشتركان في العقدتين نفسيهما.
3. Does maximum load power imply maximum efficiency?
هل استطاعة الحمل العظمى تعني الكفاءة العظمى؟
No; the simple resistive optimum has 50% efficiency.
لا؛ كفاءة الحالة المثلى في النموذج المقاومي البسيط 50%.
4. What is the role of KCL in the branch method?
ما دور قانون التيار في طريقة الفروع؟
It links branch currents by charge balance at a node.
يربط تيارات الفروع بتوازن الشحنة عند العقدة.
5. How is the shared branch current obtained from mesh currents?
كيف نستخرج تيار الفرع المشترك من تيارات الحلقات؟
Take their signed difference for opposite reference directions.
نأخذ الفرق الجبري عند تعاكس اتجاهيهما المرجعيين.
6. How are independent sources deactivated for superposition?
كيف نعطل المصادر المستقلة في التراكب؟
Voltage source: short. Current source: open. Keep dependent sources active.
مصدر الجهد: قصر. مصدر التيار: فتح. تبقى المصادر التابعة فعالة.
7. Why can power not be directly superposed?
لماذا لا نطبق التراكب مباشرة على الاستطاعة؟
It depends quadratically on voltage or current, giving cross terms.
تعتمد تربيعيًا على الجهد أو التيار وتظهر حدود مختلطة.
8. Why distinguish Helmholtz 1853 from Thévenin 1883?
لماذا نميز هلمهولتز 1853 عن ثيفينن 1883؟
The earlier foundation and the later independent publication are different historical events.
الأساس السابق والنشر المستقل اللاحق حدثان تاريخيان مختلفان.
9. What does a star–delta conversion preserve?
ماذا يحفظ تحويل النجمة والمثلث؟
Electrical behavior at the three external terminals.
السلوك الكهربائي عند الأطراف الخارجية الثلاثة.
10. What does a negative solved current mean?
ماذا يعني تيار محسوب سالب؟
The actual current flows opposite to the chosen reference.
التيار الفعلي يسري بعكس الاتجاه المرجعي المختار.

DC Circuit Methods — Interactive Quiz | اختبار تفاعلي: طرق حل دارات التيار المستمر

10 questions, 1 point each; pass at 8/10. Answers and explanations appear after grading. | 10 أسئلة، درجة لكل سؤال، والنجاح من 8/10. يظهر التصحيح والشرح بعد التقييم.

References المراجع

  1. A. Gabash, Flexible Optimal Operations of Energy Supply Networks with Renewable Energy Generation and Battery Storage. Saarbrücken, Germany: Südwestdeutscher Verlag für Hochschulschriften, 2014.
  2. S. J. Russell and P. Norvig, Artificial Intelligence: A Modern Approach, 4th Global ed. Harlow, U.K.: Pearson Education Limited, 2022.
  3. A. Gabash, “Energy Market Transition and Climate Change: A Review of TSOs–DSOs C+++ Framework from 1800 to Present,” Energies, vol. 16, no. 17, Art. no. 6139, 2023, doi: 10.3390/en16176139.
  4. S. J. D. Prince, Understanding Deep Learning. Cambridge, MA, USA: The MIT Press, 2023.
  5. A. Gabash, AI Applications in Electrical Power Systems, Version 1.0, 2026. [Online]. Available: https://aoussgabash.com