← Sessions | الجلسات

Practical Session 1 · Basic Measurements

الجلسة العملية 1 · القياسات الأساسية

Based on the semester laboratory note: components, resistor identification, Ohm’s law, series/parallel connections, and use of ammeter, voltmeter and ohmmeter.

اعتماداً على نوطة المخبر الفصلية: العناصر، قراءة المقاومات، قانون أوم، التوصيل تسلسلاً وتفرعاً، واستخدام الأميتر والفولتميتر والأوميتر.

Session procedure | خطوات الجلسة

اقرأ خطوات التجربة قبل البدء بالعمل.
1. Measure a resistor with the supply OFF.1. قِس مقاومة مع فصل المنبع.
2. Set the source and measure voltage with the voltmeter in parallel.2. اضبط المنبع وقِس الجهد بوصل الفولتميتر على التوازي.
3. Measure current with the ammeter in series.3. قِس التيار بوصل الأميتر على التسلسل.

This session reproduces the introductory work in the laboratory note before the later network theorems.

تحاكي هذه الجلسة العمل التمهيدي في النوطة قبل الانتقال إلى نظريات الدارات اللاحقة.

Skill 1 · Measure resistance (Ω)

المهارة 1 · قياس المقاومة (Ω)

Learning goal: learn how to use the multimeter as an ohmmeter.

هدف التعلم: تعلّم استخدام الملتيميتر كأوميتر لقياس المقاومة.
Work sequence | تسلسل العمل
1. Choose a resistor and place it on the bench → 2. Set the multimeter to Ω → 3. Connect the leads correctly → 4. Keep the DC source OFF → 5. Press START MEASUREMENT.1. اختر مقاومة وضعها على طاولة العمل ← 2. اضبط الملتيميتر على Ω ← 3. صِل المجسات بشكل صحيح ← 4. أبقِ منبع DC مفصولاً OFF ← 5. اضغط ابدأ القياس.

1 · Choose a resistor and place it on the bench1 · اختر مقاومة وضعها على طاولة العمل

Select a resistor to place on the bench.اختر مقاومة لوضعها على طاولة العمل.
OL
Ω
COM
BLACK
VΩ
RED
mA
RED
BLACK probeRED probe
Student controls | تحكم الطالباختر وضع الجهاز ومدخل السلك الأحمر ثم موضع المجسين.
5. DC source connection | توصيل منبع DCمطلوب لقياس الجهد والتيار، وليس لقياس المقاومة.
Make your selections, then press START MEASUREMENT.قم بالاختيارات ثم اضغط ابدأ القياس.
No measurement yet.لم يبدأ القياس بعد.
Your connection | توصيلك
RMULTIMETEROLDC SOURCEOFF
Ohmmeter · source OFFأوميتر · المنبع OFF
DC Power Supply · for voltage/current stepsمنبع توتر مستمر
0.00 V
Supply OFF | المنبع متوقف

The laboratory will tell you only if the connection is correct or needs correction.سيخبرك المخبر فقط إن كان التوصيل صحيحاً أو يحتاج إلى تصحيح.

Task A · Resistor color codeالمهمة A · شيفرة ألوان المقاومة

Identify the resistor before using the ohmmeter.

حدّد قيمة المقاومة من ألوانها قبل استخدام الأوميتر.
A. Identify component | تحديد العنصر
B. Measure resistance with source OFF | قياس المقاومة والمنبع مفصول
C. Measure voltage and current | قياس الجهد والتيار
Skill 1/3 · Resistance measurement | المهارة 1/3 · قياس المقاومة
DC SOURCE
منبع DC
R — Ω
MULTIMETER
ملتيميتر
The board changes with your selected meter mode and connection. Red/black leads show the measurement path.يتغير شكل التوصيل بحسب وظيفة جهاز القياس وطريقة الوصل، وتظهر الأسلاك الحمراء والسوداء مسار القياس.
3 · Connect the probes | صِل المجسين

Tap RED or BLACK, then tap the circuit point where that probe should touch.

اختر المجس الأحمر أو الأسود، ثم اضغط نقطة الدارة التي تريد توصيله بها.
RED: —   BLACK: —
RMeasured R (Ω)المقاومة المقاسةU (V)الجهدI (mA)التيار
—
Error equation | معادلة حساب الخطأ
Error(%) = Itheoretical − ImeasuredItheoretical × 100
Symbols: Imeasured = measured current; Itheoretical = theoretical current calculated from I = U/R; Error (%) = signed percentage error; positive means measured current is lower than theoretical, negative means it is higher.شرح الرموز: Iالمقاس = التيار المقاس؛ Iالنظري = التيار النظري المحسوب من I = U/R؛ الخطأ (%) = نسبة الخطأ المئوية بإشارتها؛ القيمة الموجبة تعني أن التيار المقاس أقل من النظري، والسالبة تعني أنه أعلى من النظري.
Calculated error | الخطأ المحسوب: —

Experiment 1 · Coulomb's Law

التجربة 1 · قانون كولوم

Adjust both charges and their separation.عدّل الشحنتين والمسافة بينهما.

F = k |q₁q₂| / r²   ,   k = 8.9875517923 × 10⁹ N·m²/C²
Simulation measurement | قياس المحاكاة: — N
Direction | الاتجاه: —
+2−3r = 0.50 mRun / شغّل
Concept check | تحقق مفاهيمي:
What happens to F if r doubles?ماذا يحدث للقوة إذا تضاعفت المسافة؟