Interactive Virtual Laboratory
المخبر الافتراضي التفاعلي
Perform the practical session, connect the instruments, take measurements, record results, then verify your calculations.
نفّذ الجلسة العملية، صِل أجهزة القياس، خذ القراءات، سجّل النتائج، ثم تحقق من حساباتك.
Basic Measurements
Components, resistor identification, Ohm’s law, series/parallel connections, and use of ammeter, voltmeter and ohmmeter.
العناصر، قراءة المقاومات، قانون أوم، التوصيل تسلسلاً وتفرعاً، واستخدام الأميتر والفولتميتر والأوميتر.
Kirchhoff’s Laws · KVL & KCL
Verify KVL in a series circuit and KCL in a parallel circuit, based on the semester laboratory note.
التحقق من قانون كيرشوف للجهد في دارة تسلسلية وقانون كيرشوف للتيار في دارة تفرعية، اعتماداً على نوطة المخبر الفصلية.
Series, Parallel & Mixed Resistor Circuits
Verify Ohm’s law for series, parallel and mixed resistor networks; measure voltage and current, determine equivalent resistance, and study the U–I characteristic.
التحقق من قانون أوم عند توصيل المقاومات تسلسلياً وتفرعياً ومختلطاً، وقياس الجهد والتيار، وحساب المقاومة المكافئة، ودراسة العلاقة بين الجهد والتيار.
Superposition Theorem
Verify superposition by activating each independent source separately, then compare the algebraic sum with the circuit containing both sources.
التحقق من نظرية التنضد بتفعيل كل منبع مستقل منفرداً ثم مقارنة المجموع الجبري مع الدارة عند وجود المنبعين معاً.
Remote Practical Session 1 · Basic Measurements
الجلسة العملية الافتراضية 1 · القياسات الأساسية
Session procedure | خطوات الجلسة
اقرأ خطوات التجربة قبل البدء بالعمل.This session reproduces the introductory work in the laboratory note before the later network theorems.
تحاكي هذه الجلسة العمل التمهيدي في النوطة قبل الانتقال إلى نظريات الدارات اللاحقة.Skill 1 · Measure resistance (Ω)
المهارة 1 · قياس المقاومة (Ω)
Learning goal: learn how to use the multimeter as an ohmmeter.
هدف التعلم: تعلّم استخدام الملتيميتر كأوميتر لقياس المقاومة.1. Choose a resistor and place it on the bench → 2. Set the multimeter to Ω → 3. Connect the leads correctly → 4. Keep the DC source OFF → 5. Press START MEASUREMENT.1. اختر مقاومة وضعها على طاولة العمل ← 2. اضبط الملتيميتر على Ω ← 3. صِل المجسات بشكل صحيح ← 4. أبقِ منبع DC مفصولاً OFF ← 5. اضغط ابدأ القياس.
1 · Choose a resistor and place it on the bench1 · اختر مقاومة وضعها على طاولة العمل
BLACK
RED
RED
The laboratory will tell you only if the connection is correct or needs correction.سيخبرك المخبر فقط إن كان التوصيل صحيحاً أو يحتاج إلى تصحيح.
Identify the resistor before using the ohmmeter.
حدّد قيمة المقاومة من ألوانها قبل استخدام الأوميتر.منبع DC
ملتيميتر
Tap RED or BLACK, then tap the circuit point where that probe should touch.
اختر المجس الأحمر أو الأسود، ثم اضغط نقطة الدارة التي تريد توصيله بها.| R | Measured R (Ω)المقاومة المقاسة | U (V)الجهد | I (mA)التيار |
|---|---|---|---|
| — |
Experiment 1 · Coulomb's Law
التجربة 1 · قانون كولوم
Adjust both charges and their separation.عدّل الشحنتين والمسافة بينهما.
Direction | الاتجاه: —
Experiment 2 · Electric Field & Superposition
التجربة 2 · الحقل الكهربائي ومبدأ التراكب
Two point charges lie on the x-axis. Calculate the net electric field at point P.شحنتان نقطيتان على محور x. احسب الحقل الكهربائي المحصل عند النقطة P.
E₁ = — N/C
E₂ = — N/C
Enet = — N/C
Direction | الاتجاه: —
Experiment 3 · Capacitors
التجربة 3 · السعات الكهربائية
Connect two capacitors in series or parallel and apply a DC voltage.صل مكثفين على التسلسل أو التوازي وطبّق جهداً مستمراً.
Ceq = — μF
Qtotal = — μC
V₁ = — V V₂ = — V
Experiment 4 · Ohm & Kirchhoff Laws
التجربة 4 · قانون أوم وقانونا كيرشوف
A source feeds R₁ in series with a parallel branch R₂ || R₃. Verify Ohm's law, KCL at node A, and KVL around each loop.يغذي المصدر المقاومة R₁ المتسلسلة مع فرع متوازٍ R₂ || R₃. تحقق من قانون أوم وKCL عند العقدة A وKVL في كل حلقة.
KCL: I₁ = I₂ + I₃ · KVL: Vₛ = V₁ + V₂ = V₁ + V₃
I₁ = — mA I₂ = — mA I₃ = — mA
V₁ = — V V₂ = — V V₃ = — V
KCL residual | باقي KCL: — mA
KVL residual | باقي KVL: — V
Experiment 5 · Thévenin & Norton Equivalents
التجربة 5 · مكافئا ثيفينن ونورتن
Find the equivalent seen by load RL. Open the load to obtain VOC, short the output to obtain ISC, then verify the equivalent with the load reconnected.أوجد المكافئ الذي يراه الحمل RL. افصل الحمل لإيجاد VOC، ثم اقصر الخرج لإيجاد ISC، وبعدها تحقق بإعادة توصيل الحمل.
RTh = R₁ || R₂ · IN = ISC = VTh/RTh
VOC = — V
ISC = — mA
RTh = — Ω
IL, original = — mA
IL, Thévenin = — mA
Experiment 6 · RC Transient
التجربة 6 · الحالة العابرة لدائرة RC
Close the switch and observe capacitor charging. Compare the simulated voltage with the theoretical exponential response.أغلق المفتاح وراقب شحن المكثف، ثم قارن جهد المحاكاة مع الاستجابة الأسية النظرية.
At t = τ: vC ≈ 0.632 Vₛ
τ = 1.000 s t = 0.000 s
vC(t) = 0.000 V (0.0% Vₛ)
The laboratory framework is ready. This experiment will be activated in the next development step. | إطار المخبر جاهز، وسيتم تفعيل هذه التجربة في خطوة التطوير التالية.